REAR SEAT OUTER BELT ASSEMBLY(for Wagon) REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR BENCH TYPE SEAT CUSHION ASSEMBLY

    Click here

  4. REMOVE REAR SIDE SEATBACK ASSEMBLY LH

    A004P9F

    1. Remove the bolt and disconnect the outer belt anchor.

    2. A004Q46

      Using a screwdriver, detach the claw to open the cap of the rear seat shoulder belt guide.

    3. Remove the seat belt from the belt guide.

    4. A004QF9

      Remove the bolt and side seatback LH.

  5. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

    Click here

  6. REMOVE ROOM PARTITION NET ASSEMBLY (w/ Partition Net)

    Click here

  7. REMOVE LOWER DECK TRIM SIDE BOARD LH (w/ Partition Board)

    Click here

  8. REMOVE DECK BOARD ASSEMBLY

    Click here

  9. REMOVE DECK BOARD SUB-ASSEMBLY

    Click here

  10. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY

    Click here

  11. REMOVE REAR DECK FLOOR BOX

    Click here

  12. REMOVE FLOOR SIDE RAIL LH (w/ Deck Rail)

    Click here

  13. REMOVE NO. 2 DECK SIDE TRIM COVER (w/o Deck Rail)

    Click here

  14. REMOVE NO. 6 DECK SIDE TRIM COVER (w/o Deck Rail)

    Click here

  15. REMOVE ROPE HOOK ASSEMBLY (w/o Deck Rail)

    Click here

  16. REMOVE DECK FLOOR BOX LH

    Click here

  17. REMOVE REAR FLOOR FINISH PLATE

    Click here

  18. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  19. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    Tech Tips

    Partially remove the rear door opening trim weatherstrip LH so that the deck trim side panel LH can be removed Click here.

  20. REMOVE BACK DOOR WEATHERSTRIP


    1. Partially remove the back door weatherstrip so that the deck trim side panel LH can be removed Click here.

  21. REMOVE INNER ROOF SIDE GARNISH CAP LH

    Click here

  22. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

    Click here

  23. REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH


    1. for LH Side:


      1. A004SQSE01
        Text in Illustration
        *a Bolt
        *b Nut

        Remove the bolt and nut.

      2. Detach the guide and remove the rear seat 3 point type belt assembly LH.

      3. A004P4QE02
        Text in Illustration
        *1 Locking Button
        *a Protective Tape

        Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector as shown in the illustration.

        Tech Tips

        Tape the screwdriver tip before use.

    2. for RH Side:


      1. A004TFTE02
        Text in Illustration
        *1 Locking Button
        *a Protective Tape

        Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector as shown in the illustration.

        Tech Tips

        Tape the screwdriver tip before use.

      2. A004RQ8E01
        Text in Illustration
        *a Bolt
        *b Nut

        Using a clip remover, detach the wire harness clamp (A).

      3. Remove the bolt and nut.

      4. Detach the guide and remove the rear seat 3 point type belt assembly LH.

  24. REMOVE OUTER BELT ANCHOR BRACKET SUB-ASSEMBLY LH

    A004TEV

    1. Remove the 2 bolts.

    2. Detach the 2 guides and remove the outer belt anchor bracket sub-assembly LH.