FRONT POWER SEAT MOTOR ASSEMBLY(for Reclining) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL POWER SEAT MOTOR ASSEMBLY (for Reclining)


    1. A004UA0

      Remove the 2 holders together with the 2 inner reclining rods from the reclining rod.

    2. A004RGS

      Remove the inner reclining rod and push nut from the holder.

    3. A004NRP

      Remove the inner reclining rod and push nut from the holder.

    4. A004R5D

      Install the 2 holders to the reclining rod.

    5. A004UEG

      Install the push nut to the holder.

      Note

      Make sure the direction of the push nut is as shown in the illustration.

    6. A004OSJ

      Install the push nut to the holder.

      Note

      Make sure the direction of the push nut is as shown in the illustration.

    7. Clean the threads of the bolt for the power seat motor assembly with non-residue solvent.

    8. Apply adhesive to the threads of the bolt for the power seat motor assembly.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
    9. A004P68

      Temporarily install the power seat motor assembly with the bolt.

    10. A004OZZ

      Push in the inner reclining rod as shown in the illustration.

    11. A004NM5

      Push in the inner reclining rod as shown in the illustration.

    12. A004MMT

      Push in the 2 inner reclining rods in alternating passes to install them

      Note

      Make sure that the holder does not interfere with the power seat motor assembly or front seatback frame.

    13. Tighten the bolt.

      Torque:
      4.5 N*m  { 46 kgf*cm, 40 in.*lbf }
    14. A004U7F

      Attach the 8 hooks to install the seatback spring.

    15. A004U9H

      Connect the 2 connectors.

    16. A004NTG

      for Driver Side:

      Connect the connector.

  2. INSTALL SEPARATE TYPE FRONT SEATBACK PAD

    Click here

  3. INSTALL SEPARATE TYPE FRONT SEATBACK COVER

    Click here

  4. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

    Click here

  5. INSTALL FRONT SEAT INNER CUSHION SHIELD LH

    Click here

  6. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

    Click here

  7. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)

    Click here

  8. INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR (for Driver Side)

    Click here

  9. INSTALL FRONT POWER SEAT SWITCH LH

    Click here

  10. INSTALL FRONT SEAT CUSHION SHIELD LH WITH FRONT SEAT NO. 1 INNER CUSHION SHIELD LH

    Click here

  11. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

    Click here

  12. INSTALL RECLINING POWER SEAT SWITCH KNOB

    Click here

  13. INSTALL FRONT SEAT ASSEMBLY

    Click here

  14. CHECK SRS WARNING LIGHT

    Click here

  15. INSPECT FRONT SEAT ASSEMBLY


    1. Check the power seat operation Click here.

    2. Check the seat heater operation.


      1. Turn the ignition switch to ON.

      2. Operate the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.