FRONT SEAT ASSEMBLY(for Manual Seat) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)

    Click here

  2. INSTALL REAR UPPER NO. 2 SEAT TRACK COVER


    1. A004NND

      Attach the 3 claws to install the rear upper No. 2 seat track cover.

  3. INSTALL REAR UPPER SEAT TRACK COVER


    1. A004T1W

      Attach the 3 claws to install the rear upper seat track cover.

  4. INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

    A004MU0

    1. Attach the 8 hooks to install the separate type front seat cushion spring assembly to the front seat adjuster assembly LH.

    2. A004OI9

      for Front Passenger Side:

      Attach the 2 clamps to install the connector holder.

  5. INSTALL FRONT SEAT ADJUSTER ASSEMBLY LH


    1. A004U02

      Using a T50 "TORX" socket wrench, install the front seat adjuster assembly LH with the 4 "TORX" bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

  6. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)

    A004REP

    1. Attach the guide to install the front seat lower cushion shield LH with the screw.

  7. INSTALL FRONT SEAT WIRE LH (w/ Lumbar Support)


    1. A004OC9

      Attach the claw to install the front seat wire LH.

    2. Connect the connector.

    3. Attach the 2 wire harness clamps.

    4. A004TSM

      Attach the 2 wire harness clamps to install the front seat wire LH.

  8. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (w/ Seat Heater System)


    1. A004PY0

      Attach the claw to install the seat climate control controller LH.

  9. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH

    Click here

  10. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar Support)

    Click here

  11. INSTALL SEPARATE TYPE FRONT SEATBACK PAD


    1. A004PYG

      Install the separate type front seatback pad.

  12. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)

    Click here

  13. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. Temporarily install the separate type front seatback cover.

    2. A004N29E01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 3 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    3. A004S71E01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 3 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    4. A004OAFE02
      Text in Illustration
      *1 Hog Ring Pliers
      *2 Hog Ring
      *3 Hook

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    5. Attach the 2 hooks.

    6. A004O2DE02
      Text in Illustration
      *1 Hog Ring Pliers
      *2 Strap

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 5 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

      • When installing the separate type front seatback cover, make sure to pass the straps of the separate type front seatback cover through the hog rings.

    7. A004NKU

      Attach the 2 claws to install the 2 front seat headrest supports.

    8. A004T2G

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

    9. A004RLR

      Attach the 2 hooks.

    10. A004Q05

      Attach the 2 hooks to connect the 2 straps.

    11. A004SOJ

      Attach the hook at the bottom of the separate type front seatback cover.

    12. A004PFU

      Attach the 2 hooks.

  14. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

    Tech Tips

    Perform this procedure when it is necessary to remove and reinstall or replace the separate type front seatback assembly.


    1. A004NVY

      Using a T50 "TORX" socket wrench, install the separate type front seatback assembly to the front seat adjuster assembly LH with the 4 "TORX" bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

    2. w/ Lumbar Support:


      1. A004TKA

        Attach the 2 wire harness clamps.

      2. Connect the connector.

      3. A004T2G

        Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

      4. A004RLR

        Attach the 2 hooks.

      5. A004Q05

        Attach the 2 hooks to connect the 2 straps.

      6. A004SOJ

        Attach the hook at the bottom of the separate type front seatback cover.

    3. A004PFU

      Attach the 2 hooks.

    4. A004O06

      Attach the claw and connect the connector.

    5. Attach the 2 wire harness clamps.

  15. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)

    Click here

  16. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A004S2O

      Attach the 13 hooks to install the separate type front seat cushion cover to the separate type front seat cushion pad.

      Note


      • Be careful not to damage the separate type front seat cushion cover.

      • When attaching the hooks, avoid wrinkling the separate type front seat cushion cover.

  17. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


    1. Attach the 9 hooks to install the separate type front seat cushion cover with pad.

      A004PSJ
    2. A004S3R

      w/ Lumbar Support:

      Attach the wire harness clamp.

    3. A004NWM

      for Front Passenger Side:

      Attach the claw to connect the connector.

    4. w/ Seat Heater System:


      1. A004S9A

        Connect the connector.

      2. A004QQO

        Attach the claw to connect the connector.

      3. Attach the wire harness clamp.

      4. Connect the 2 connectors.

    5. A004MK1

      Attach the 2 hooks.

  18. INSTALL FRONT OUTER SEAT CUSHION BRACKET (for Driver Side)


    1. A004Q2H

      Attach the 4 claws to install the front seat hinge pin and front outer seat cushion bracket to the connector link.

    2. A004RR6

      Attach the 2 claws to install the vertical adjuster handle bracket with connector link.

    3. A004OURE01
      Text in Illustration
      *1 Connector Link

      Connect the connector link and install the clip.

  19. INSTALL RECLINING CONTROL LEVER LH


    1. Temporarily install the reclining control lever LH with the 2 nuts.

    2. A004P51E02
      Text in Illustration
      *1 Nut A
      *2 Nut B

      Using a 15 mm socket wrench, tighten nut B.

      Torque:
      for Nut B
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

    3. Tighten nut A.

      Torque:
      for Nut A
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }
    4. A004PVN

      Attach the 2 hooks to install the spring.

  20. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. A004N6C

      Attach the hook to install the front seat inner cushion shield LH with the screw.

  21. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

    Click here

  22. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)

    Click here

  23. INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR (for Driver Side)


    1. A004QCY

      Attach the 2 clamps and connect the wire harness.

    2. A004T0E

      Attach the 2 claws and 2 guides to install the seat slide position sensor protector with the screw.

  24. INSTALL LUMBAR FRONT POWER SEAT SWITCH (w/ Lumbar Support)

    Click here

  25. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. A004PEA

      w/ Lumbar Support:

      Connect the connector.

    2. A004QKJ

      Attach the claw and hook to install the front seat cushion shield LH.

    3. Install the 2 screws.

    4. A004TLU

      Attach the 2 rubber bands.

  26. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. A004MSQ

      Attach the claw to install the reclining adjuster release handle LH.

  27. INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side)


    1. A004NG6

      Install the vertical adjusting handle LH with the 2 screws.

  28. INSTALL VERTICAL SEAT ADJUSTER KNOB CAP (for Driver Side)


    1. A004QJM

      Attach the 3 claws to install the vertical seat adjuster knob cap.