FRONT SEAT ASSEMBLY(for Manual Seat) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL NO. 2 REAR UPPER SEAT TRACK COVER


    1. A004SIP

      Attach the 3 claws to install the No. 2 rear upper seat track cover.

  2. INSTALL REAR UPPER SEAT TRACK COVER


    1. A004MZ5

      Attach the 3 claws to install the rear upper seat track cover.

  3. INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

    A004MU0

    1. Attach the 8 hooks to install the separate type front seat cushion spring assembly to the front seat adjuster assembly LH.

  4. INSTALL FRONT SEAT ADJUSTER ASSEMBLY LH


    1. A004NHX

      Using a T50 "TORX" socket wrench, install the front seat adjuster assembly LH with the 4 "TORX" bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

  5. INSTALL FRONT SEAT INNER BELT ANCHOR BRACKET COVER LH

    A004O47

    1. Install the front seat inner belt anchor bracket cover LH with the screw.

  6. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH

    A004RWS

    1. Install the front seat lower cushion shield LH with the screw.

  7. INSTALL FRONT SEAT WIRE LH (w/ Lumbar Support)


    1. A004PKY

      Attach the claw to install the front seat wire LH.

    2. Attach the 3 wire harness clamps.

    3. A004P24

      Attach the wire harness clamp.

  8. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (w/ Seat Heater System)


    1. A004SIQ

      Attach the claw to install the seat climate control controller LH.

    2. Connect the connector.

  9. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH

    Click here

  10. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar Support)

    Click here

  11. INSTALL FRONT SEATBACK HEATER ASSEMBLY

    Click here

  12. INSTALL SEPARATE TYPE FRONT SEATBACK PAD

    A004Q2U

    1. Install the separate type front seatback pad.

  13. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. A004SNI

      Attach the 2 hooks.

    2. A004PV8

      Attach the 2 claws to install the 2 front seat headrest supports.

    3. A004SKV

      Install the front seat headrest assembly.

      Note

      Push in the front seat headrest assembly until the headrest lock engages.

    4. A004P3Y

      Pass the cable through the hole of the seatback frame.

    5. A004N9Z

      Attach the 2 claws to install the clip.

    6. A004T8UE02
      Text in Illustration
      *1 Cable End

      Pull the cable through the clip until the cable end reaches the clip.

    7. A004NUA

      Install a new cable tie.

    8. A004MVZE02
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 2 hooks to close the seatback mat.

    9. A004RX9

      Attach the 2 claws to connect the cable to the active headrest lower unit.

    10. Using hog ring pliers, install a new hog ring.

    11. A004QXA

      Attach the 2 claws to install the active headrest lower unit.

    12. A004TY5E02
      Text in Illustration
      *1 Cable End
      A004NPW Pull

      Pull the cable and connect the cable end to the active headrest lower unit.

    13. A004TCD

      Attach the 7 hooks to install the actuator shield.

    14. A004R88E02
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 3 hooks.

    15. Using hog ring pliers, install the upper part of the separate type front seatback cover to the separate type front seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    16. A004MMIE02
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the seatback cover bracket with the screw.

      Note

      After the separate type front seatback cover is installed, make sure the seatback cover bracket is not twisted.

    17. A004T2G

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

    18. A004U0S

      Attach the 2 hooks to connect the 2 straps.

    19. A004R1S

      Attach the 2 hooks at the bottom of the separate type front seatback cover.

    20. Attach the 2 hooks.

      A004SW5

  14. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

    Tech Tips

    Perform this procedure when it is necessary to remove and reinstall or replace the separate type front seatback assembly.


    1. A004SF6

      Using a T50 "TORX" socket wrench, install the separate type front seatback assembly to the front seat adjuster assembly LH with the 4 "TORX" bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

    2. Attach the 2 wire harness clamps.

    3. A004ORX

      Attach the connector.

    4. A004SKV

      Install the front seat headrest assembly.

      Note

      Push in the front seat headrest assembly until the headrest lock engages.

    5. A004P3Y

      Pass the cable through the hole of the seatback frame.

    6. A004N9Z

      Attach the 2 claws to install the clip.

    7. A004T8UE02
      Text in Illustration
      *1 Cable End

      Pull the cable through the clip until the cable end reaches the clip.

    8. A004NUA

      Install a new cable tie.

    9. A004MVZE02
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 2 hooks to close the seatback mat.

    10. Using hog ring pliers, install a new hog ring.

    11. A004RX9

      Attach the 2 claws to connect the cable to the active headrest lower unit.

    12. A004QXA

      Attach the 2 claws to install the active headrest lower unit.

    13. A004TY5E02
      Text in Illustration
      *1 Cable End
      A004NPW Pull

      Pull the cable and connect the cable end to the active headrest lower unit.

    14. A004TCD

      Attach the 7 hooks to install the actuator shield.

    15. A004R88E02
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 3 hooks.

    16. Using hog ring pliers, install the upper part of the separate type front seatback cover to the separate type front seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    17. A004MMIE02
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the seatback cover bracket with the screw.

      Note

      After the separate type front seatback cover is installed, make sure the seatback cover bracket is not twisted.

    18. w/ Lumbar Support:


      1. A004PT3

        Connect the connector.

      2. A004P24

        Attach the wire harness clamp.

    19. A004T2G

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

    20. A004U0S

      Attach the 2 hooks to connect the 2 straps.

    21. A004R1S

      Attach the 2 hooks at the bottom of the separate type front seatback cover.

    22. Attach the 2 hooks.

      A004SW5

  15. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)

    Click here

  16. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A004MYY

      Attach the hooks to install the separate type front seat cushion cover to the separate type front seat cushion pad.

      Note


      • Be careful not to damage the cover.

      • When attaching the hooks, avoid wrinkling the cover.

  17. INSTALL SEAT CUSHION COVER WITH PAD


    1. Attach the hooks to install the seat cushion cover with pad.

      A004N58E02
      Text in Illustration
      *A w/ Seat Heater System - -

    2. w/ Seat Heater System:

      Connect the connector.

    3. A004PCR

      w/ Lumbar Support:

      Attach the wire harness clamp.

    4. A004U2Y

      for Front Passenger Side:

      Attach the 2 hooks to connect the connector holder.

    5. w/ Seat Heater System:


      1. A004NVK

        Connect the connector.

      2. A004SG6

        Install a new cable tie.

    6. for Driver Side:


      1. A004RR6

        Attach the 2 claws to install the vertical adjuster handle bracket with connector link.

      2. A004OURE01
        Text in Illustration
        *1 Connector Link

        Connect the connector link and install the clip.

    7. A004P2O

      Using a 15 mm socket wrench, install the reclining handle with the nut.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }
    8. A004TKO

      Install the spring.

  18. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    Click here

  19. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. A004OT9E02
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Attach the wire harness clamp and hook to install the front seat inner cushion shield LH.

    2. Install the 2 screws.

  20. INSTALL LUMBAR FRONT POWER SEAT SWITCH (w/ Lumbar Support)

    Click here

  21. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. A004PEA

      w/ Lumbar Support:

      Connect the connector.

    2. A004QKJ

      Attach the claw and hook to install the front seat cushion shield LH.

    3. Install the 2 screws.

    4. A004PTI

      Attach the 2 rubber bands.

  22. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. A004MSQ

      Attach the claw to install the reclining adjuster release handle LH.

  23. INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side)


    1. A004NG6

      Install the vertical adjusting handle LH with the 2 screws.

  24. INSTALL VERTICAL SEAT ADJUSTER KNOB CAP (for Driver Side)


    1. A004QJM

      Attach the 3 claws to install the vertical seat adjuster knob cap.