FRONT SEAT ASSEMBLY(for Power Seat) DISASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. REMOVE RECLINING POWER SEAT SWITCH KNOB


    1. A004RS9E03
      Text in Illustration
      *1 Protective Tape

      Apply protective tape around the front seat cushion shield LH.

    2. Using a screwdriver, detach the 2 claws and remove the reclining power seat switch knob.

      Tech Tips

      Tape the screwdriver tip before use.

  2. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A004POME02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 4 claws and remove the slide and vertical power seat switch knob.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE FRONT SEAT CUSHION SHIELD LH WITH FRONT SEAT NO. 1 INNER CUSHION SHIELD LH


    1. A004PWU

      Detach the 2 rubber bands.

    2. A004NVA

      Remove the 2 screws and detach the 2 claws.

    3. A004QS3

      Remove the 2 screws.

    4. Pull the front seat cushion shield LH to detach the hook and remove the front seat cushion shield LH with front seat No. 1 inner cushion shield.

    5. A004SPB

      for Driver Side:

      Disconnect the connector.

  4. REMOVE FRONT SEAT NO. 1 INNER CUSHION SHIELD LH


    1. A004PM1

      Detach the 2 claws and remove the front seat No. 1 inner cushion shield from the front seat cushion shield LH.

  5. REMOVE LUMBAR FRONT POWER SEAT SWITCH (for Driver Side)

    Click here

  6. REMOVE FRONT POWER SEAT SWITCH

    Click here

  7. REMOVE FRONT SEAT INNER CUSHION SHIELD LH


    1. A004SKDE02
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Remove the 2 screws.

    2. Pull the front seat inner cushion shield LH to detach the hook and remove it.

    3. Detach the wire harness clamp.

  8. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH

    Click here

  9. REMOVE SEAT CUSHION COVER WITH PAD


    1. A004TPD

      Disconnect the connector.

    2. A004Q70

      Cut off the cable tie.

    3. A004U2Y

      for Front Passenger Side:

      Detach the 2 hooks and disconnect the connector holder.

    4. A004PCR

      for Driver Side:

      Detach the wire harness clamp.

    5. Disconnect the 2 connectors.

      A004PM5

    6. Detach the hooks and remove the seat cushion cover with pad.

  10. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A004MYY

      Detach the hooks and remove the separate type front seat cushion cover from the separate type front seat cushion pad.

      Note


      • As the front seat cushion heater assembly is affixed to the separate type front seat cushion pad, do not remove the front seat cushion heater assembly from the separate type front seat cushion pad.

      • When replacing either the front seat cushion heater assembly or separate type front seat cushion pad due to a malfunction, be sure to replace both of them with new parts.

  11. REMOVE POWER SEAT MOTOR ASSEMBLY (for Front Vertical)

    Click here

  12. REMOVE POWER SEAT MOTOR ASSEMBLY (for Rear Lifter)

    Click here

  13. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY LH

    Tech Tips

    Perform this procedure when it is necessary to remove and reinstall or replace the separate type front seatback assembly LH.


    1. Detach the 2 hooks.

      A004TVB
    2. A004R1S

      Detach the 2 hooks from the bottom of the separate type front seatback cover.

    3. A004S64

      Detach the 2 hooks and disconnect the 2 straps.

    4. A004RL8

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the surface.

    5. A004P24

      Detach the wire harness clamp.

    6. A004MU6

      for Driver Side:

      Disconnect the 2 connectors and detach the wire harness clamp.

    7. A004RIR

      for Front Passenger Side:

      Disconnect the connector and detach the wire harness clamp.

    8. A004MMIE02
      Text in Illustration
      *1 Seatback Cover Bracket

      Remove the screw and detach the seatback cover bracket.

    9. A004RAWE01
      Text in Illustration
      *1 Hook
      *2 Hog Ring

      Remove the hog rings and detach the 3 hooks from the center of the separate type front seatback pad.

    10. A004TCD

      Detach the 7 hooks and remove the actuator shield.

    11. A004NRZE02
      Text in Illustration
      *1 Cable End
      A004NAK Pull

      Pull the cable to loosen it, and then disconnect the cable end from the active headrest lower unit.

    12. A004P8Y

      Detach the 2 claws and remove the active headrest lower unit.

    13. A004RX9

      Using a screwdriver, detach the 2 claws and disconnect the cable.

    14. A004N91E02
      Text in Illustration
      *1 Hook
      *2 Hog Ring

      Remove the hog ring and detach the 2 hooks and open the seatback mat.

    15. A004NUA

      Cut off the cable tie.

    16. A004RR1E02
      Text in Illustration
      *1 Cable End

      Push the cable to push out the cable end from the clip.

    17. A004N9Z

      Detach the 2 claws and remove the clip.

    18. A004QAS

      Pull the cable through the hole of the seatback frame.

    19. A004RTAE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, push the headrest support lock to release the lock and remove the front seat headrest assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    20. A004O1Z

      Detach the connector.

    21. A004MW5

      Detach the 4 wire harness clamps.

    22. A004QHP

      Using a T50 "TORX" socket wrench, remove the 4 "TORX" bolts and separate type front seatback assembly LH from the front seat adjuster assembly LH.

  14. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    1. Detach the 2 hooks.

      A004TVB
    2. A004R1S

      Detach the 2 hooks from the bottom of the separate type front seatback cover.

    3. A004S64

      Detach the 2 hooks and disconnect the 2 straps.

    4. A004RL8

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the surface.

    5. A004MMIE02
      Text in Illustration
      *1 Seatback Cover Bracket

      Remove the screw and detach the seatback cover bracket.

    6. A004RAWE01
      Text in Illustration
      *1 Hook
      *2 Hog Ring

      Remove the hog rings and detach the 3 hooks from the center of the separate type front seatback pad.

    7. A004TCD

      Detach the 7 hooks and remove the actuator shield.

    8. A004NRZE02
      Text in Illustration
      *1 Cable End
      A004NAK Pull

      Pull the cable to loosen it, and then disconnect the cable end from the active headrest lower unit.

    9. A004P8Y

      Detach the 2 claws and remove the active headrest lower unit.

    10. A004RX9

      Using a screwdriver, detach the 2 claws and disconnect the cable.

    11. A004N91E02
      Text in Illustration
      *1 Hook
      *2 Hog Ring

      Remove the hog ring and detach the 2 hooks and open the seatback mat.

    12. A004NUA

      Cut off the cable tie.

    13. A004RR1E02
      Text in Illustration
      *1 Cable End

      Push the cable to push out the cable end from the clip.

    14. A004N9Z

      Detach the 2 claws and remove the clip.

    15. A004QAS

      Pull the cable through the hole of the seatback frame.

    16. A004RTAE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, push the headrest support lock to release the lock and remove the front seat headrest assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    17. A004QS2

      Detach the 2 claws and remove the 2 front seat headrest supports.

    18. A004SNI

      Detach the 2 hooks and remove the separate type front seatback cover.

  15. REMOVE SEPARATE TYPE FRONT SEATBACK PAD

    A004U0X

    1. Remove the separate type front seatback pad.

      Note


      • As the front seatback heater assembly is affixed to the separate type front seatback pad, do not remove the front seatback heater assembly from the separate type front seatback pad.

      • When replacing either the front seatback heater assembly or separate type front seatback pad due to a malfunction, be sure to replace both of them with new parts.

  16. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH

    Click here

  17. REMOVE FRONT SEAT AIRBAG ASSEMBLY LH

    Click here

  18. REMOVE POWER SEAT MOTOR ASSEMBLY (for Reclining)

    Click here

  19. REMOVE SEAT CLIMATE CONTROL CONTROLLER LH


    1. A004R08

      Disconnect the connector.

    2. Detach the claw and remove the seat climate control controller LH.

  20. REMOVE POSITION CONTROL ECU ASSEMBLY (for Driver Side)


    1. A004SOO

      Disconnect the 2 connectors.

    2. Remove the 2 bolts and position control ECU assembly.

  21. REMOVE FRONT SEAT WIRE LH


    1. A004UBQ

      Detach the wire harness clamp.

    2. A004P24

      Detach the wire harness clamp.

    3. A004QBB

      Disconnect the connector and detach the 3 wire harness clamps.

    4. Detach the 3 claws and remove the front seat wire LH.

  22. REMOVE FRONT SEAT LOWER CUSHION SHIELD LH


    1. A004RWS

      Remove the screw and front seat lower cushion shield LH.

  23. REMOVE FRONT SEAT INNER BELT ANCHOR BRACKET COVER LH


    1. A004O47

      Remove the screw and front seat inner belt anchor bracket cover LH.

  24. REMOVE FRONT SEAT ADJUSTER ASSEMBLY LH


    1. A004NL5

      Detach the 4 wire harness clamps.

    2. Using a T50 "TORX" socket wrench, remove the 4 "TORX" bolts and front seat adjuster assembly LH.

  25. REMOVE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY


    1. A004QJ6

      Detach the 8 hooks and remove the separate type front seat cushion spring assembly from the front seat adjuster assembly LH.

  26. REMOVE REAR UPPER SEAT TRACK COVER


    1. A004T7W

      Detach the 3 claws and remove the rear upper seat track cover.

  27. REMOVE NO. 2 REAR UPPER SEAT TRACK COVER


    1. A004O8O

      Detach the 3 claws and remove the No. 2 rear upper seat track cover.