CAN COMMUNICATION SYSTEM Open in One Side of CAN Branch Line

DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the GTS "Bus Check" screen, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).

Symptom Trouble Area
2 or more ECUs and/or sensors do not appear on the GTS "Bus Check" screen.

  • Brake actuator assembly (skid control ECU)

  • Parking brake with bracket actuator assembly (parking brake ECU)

  • Certification ECU (smart key ECU assembly)*1

  • Power steering ECU assembly

  • Air conditioning amplifier assembly*2

  • Spiral with sensor cable sub-assembly (steering angle sensor)

  • Yaw rate sensor

  • Main body ECU (instrument panel junction block assembly)

  • Radio and display receiver assembly*3

  • Headlight swivel ECU assembly*4

  • Headlight leveling ECU assembly*5

  • Power management control ECU*1

  • Center airbag sensor assembly

  • Pre-crash safety city sensor*6

  • Engine stop and start ECU

  • CAN branch wire or connector

WIRING DIAGRAM

A004OTAE02
A004NU5E02
A004RCSE02
w/ Entry and Start System
*a Power Management Control ECU
*b Yaw Rate Sensor
*c Combination Meter Assembly
*d No. 3 Junction Connector
A004TBFE02
A004QJVE02
A004N3DE02

CAUTION / NOTICE / HINT

Note


  • For vehicles with an entry and start system:

    Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) Click here.

  • As the door control battery is installed between the vehicle battery and main body ECU (instrument panel junction block assembly), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (instrument panel junction block assembly) before performing this troubleshooting procedure Click here.

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

Tech Tips


  • Perform the following inspection for the ECUs (sensors) which are displayed on the GTS. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.

  • Do not remove the combination meter assembly and ECM as they are the end parts of the circuit. If removed, CAN communication will not be possible

  • The open circuit confirmation of the combination meter assembly, ECM and CAN main wire is performed in the Check CAN Bus Line procedure of "How to Proceed with Troubleshooting". This inspection only has procedures for checking for an open circuit on one side of a CAN branch wire.

PROCEDURE


  1. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU)


    1. Disconnect the A84 brake actuator assembly (skid control ECU) connector.

    2. Select "Bus Check" on the GTS Click here.

      Result
      Result Proceed to
      "Skid Control (ABS/VSC/TRAC)" is not displayed on the GTS A
      Several ECUs and sensors in addition to "Skid Control (ABS/VSC/TRAC)" are displayed on the GTS B

    B

    CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (PARKING BRAKE ECU) Click here

    A

  2. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE)


    1. A004UA6E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Brake Actuator Assembly [Skid Control ECU])

      Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A84-2 (CANH) - A84-16 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU)

  3. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (PARKING BRAKE ECU)


    1. Disconnect the I1 parking brake with bracket actuator assembly (parking brake ECU) connector.

    2. Select "Bus Check" on the GTS Click here.

      Result
      Result Proceed to
      "Electric Parking Brake" is not displayed on the GTS A
      Several ECUs and sensors in addition to "Electric Parking Brake" are displayed on the GTS B

    B

    CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CERTIFICATION ECU) Click here

    A

  4. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (PARKING BRAKE ECU CAN BRANCH WIRE)


    1. A004QQ3E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Electric Parking Brake with Bracket Actuator Assembly [Parking Brake ECU])

      Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      I1-11 (CANH) - I1-23 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE PARKING BRAKE WITH BRACKET ACTUATOR ASSEMBLY (PARKING BRAKE ECU) Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (PARKING BRAKE ECU)

  5. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CERTIFICATION ECU)

    Note

    For vehicles without an entry and start system, go to "Check for Open in One Side of CAN Branch Wire (Power Steering ECU Assembly)".


    1. Disconnect the D54 certification ECU (smart key ECU assembly) connector.

    2. Select "Bus Check" on the GTS Click here.

      Result
      Result Proceed to
      "Certification (Smart)" is not displayed on the GTS A
      Several ECUs and sensors in addition to "Certification (Smart)" are displayed on the GTS B

    B

    CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY) Click here

    A

  6. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CERTIFICATION ECU CAN BRANCH WIRE)


    1. A004OTTE02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Certification ECU [Smart Key ECU Assembly])

      Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D54-9 (CANH) - D54-10 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CERTIFICATION ECU)

  7. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY)


    1. Disconnect the D50 power steering ECU assembly connector.

    2. Select "Bus Check" on the GTS Click here.

      Result
      Result Proceed to
      "Power Steering (EPS)" is not displayed on the GTS A
      Several ECUs and sensors in addition to "Power Steering (EPS)" are displayed on the GTS B

    B

    CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY) Click here

    A

  8. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE)


    1. A004Q9KE02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Power Steering ECU Assembly)

      Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D50-1 (CANH) - D50-7 (CANL) Ignition switch off 54 to 69 Ω
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    A

    REPLACE POWER STEERING ECU ASSEMBLY Click here

    B

    REPLACE POWER STEERING ECU ASSEMBLY Click here

    C

    REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY)

  9. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)

    Note

    For vehicles with an entry and start system, go to "Check for Open in One Side of CAN Branch Wire (Steering Angle Sensor)".


    1. Disconnect the D47*1 or D101*2 air conditioning amplifier assembly connector.


      • *1: for Automatic Air Conditioning System

      • *2: for Manual Air Conditioning System and w/o Air Conditioning System

    2. Select "Bus Check" on the GTS Click here.

      Result
      Result Proceed to
      "Air Conditioning Amplifier" is not displayed on the GTS A
      Several ECUs and sensors in addition to "Air Conditioning Amplifier" are displayed on the GTS B

    B

    CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR) Click here

    A

  10. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)


    1. A004NV1E02
      Text in Illustration
      *A for Automatic Air Conditioning System
      *B for Manual Air Conditioning System and w/o Air Conditioning System
      *a

      Rear view of wire harness connector

      (to Air Conditioning Amplifier Assembly)

      Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for Automatic Air Conditioning System
      Tester Connection Switch Condition Specified Condition
      D47-11 (CANH) - D47-12 (CANL) Ignition switch off 54 to 69 Ω
      for Manual Air Conditioning System and w/o Air Conditioning System
      Tester Connection Switch Condition Specified Condition
      D101-11 (CANH) - D101- 12 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY)

  11. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR)


    1. Disconnect the D167 spiral with sensor cable sub-assembly (steering angle sensor) connector.

    2. Select "Bus Check" on the GTS Click here.

      Result
      Result Proceed to
      "Spiral cable (Steering Angle Sensor)" is not displayed on the GTS A
      Several ECUs and sensors in addition to "Spiral cable (Steering Angle Sensor)" are displayed on the GTS B

    B

    CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR) Click here

    A

  12. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)


    1. A004S0LE02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])

      Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D167-4 (CANH) - D167-3 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR)

  13. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR)


    1. Disconnect the D69 yaw rate sensor connector.

    2. Select "Bus Check" on the GTS Click here.

      Result
      Result Proceed to
      "Yaw Rate Sensor" is not displayed on the GTS A
      Several ECUs and sensors in addition to "Yaw Rate Sensor" are displayed on the GTS B

    B

    CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU) Click here

    A

  14. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR CAN BRANCH WIRE)


    1. A004RQ3E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Yaw Rate Sensor)

      Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D69-2 (CANH) - D69-3 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE YAW RATE SENSOR Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (YAW RATE SENSOR)

  15. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU)


    1. Disconnect the D81 main body ECU (instrument panel junction block assembly) connector.

    2. Select "Bus Check" on the GTS Click here.

      Result
      Result Proceed to
      "Main Body" is not displayed on the GTS A
      Several ECUs and sensors in addition to "Main Body" are displayed on the GTS B

    B

    CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY) Click here

    A

  16. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU CAN BRANCH WIRE)


    1. A004RO7E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Main Body ECU [Instrument Panel Junction Block Assembly])

      Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D81-15 (CANH) - D81-16 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (MAIN BODY ECU)

  17. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)

    Note

    For vehicles without a radio and display type, go to "Check for Open in One Side of CAN Branch Wire (Headlight ECU)".


    1. Disconnect the D124 radio and display receiver assembly connector.

    2. Select "Bus Check" on the GTS Click here.

      Result
      Result Proceed to
      "Display and Navigation (AVN)" is not displayed on the GTS A
      Several ECUs and sensors in addition to "Display and Navigation (AVN)" are displayed on the GTS B

    B

    CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (HEADLIGHT ECU) Click here

    A

  18. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE)


    1. A004TW2E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Radio and Display Receiver Assembly)

      Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D124-9 (CANH) - D124-10 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY)

  19. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (HEADLIGHT ECU)

    Note

    For vehicles with an entry and start system or without an entry and start system, halogen headlight, go to "Check for Open in One Side of CAN Branch Wire (Power Management Control ECU)".


    1. Disconnect the A38 headlight swivel ECU assembly*1 or A82 headlight leveling ECU assembly*2 connector.


      • *1: w/ Adaptive Front-lighting System

      • *2: w/o Adaptive Front-lighting System

    2. Select "Bus Check" on the GTS Click here.

      Result
      Result Proceed to
      "Headlight swivel (AFS)" is not displayed on the GTS A
      Several ECUs and sensors in addition to "Headlight swivel (AFS)" are displayed on the GTS B

    B

    CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER MANAGEMENT CONTROL ECU) Click here

    A

  20. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (HEADLIGHT ECU CAN BRANCH WIRE)


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. A004TIEE02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Headlight Swivel ECU Assembly)

      w/ Adaptive Front-lighting System:


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        A38-12 (CANH) - A38-13 (CANL) Ignition switch off 54 to 69 Ω
    3. A004PWPE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Headlight Leveling ECU Assembly)

      w/o Adaptive Front-lighting System:


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        A82-6 (CANH) - A82-7 (CANL) Ignition switch off 54 to 69 Ω
      Result
      Result Proceed to
      OK (w/ Adaptive Front-lighting System) A
      OK (for LHD, w/o Adaptive Front-lighting System) B
      OK (for RHD, w/o Adaptive Front-lighting System) C
      NG D

    A

    REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY Click here

    B

    REPLACE HEADLIGHT LEVELING ECU ASSEMBLY Click here

    C

    REPLACE HEADLIGHT LEVELING ECU ASSEMBLY Click here

    D

    REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (HEADLIGHT ECU)

  21. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER MANAGEMENT CONTROL ECU)

    Note

    For vehicles without an entry and start system, go to "Check for Open in One Side of CAN Branch Wire (Pre-crash Safety City Sensor)".


    1. Disconnect the D111 power management control ECU connector.

    2. Select "Bus Check" on the GTS Click here.

      Result
      Result Proceed to
      "Power Management1" is not displayed on the GTS A
      Several ECUs and sensors in addition to "Power Management1" are displayed on the GTS B

    B

    CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (PRE-CRASH SAFETY CITY SENSOR) Click here

    A

  22. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER MANAGEMENT CONTROL ECU CAN BRANCH WIRE)


    1. A004OCBE02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Power Management Control ECU)

      Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D111-14 (CA1H) - D111-13 (CA1L) Ignition switch off 54 to 69 Ω

    OK

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (POWER MANAGEMENT CONTROL ECU)

  23. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (PRE-CRASH SAFETY CITY SENSOR)

    Note

    For vehicles without an entry and start system, go to "Check for Open in One Side of CAN Branch Wire (Engine Stop and Start ECU)".


    1. Disconnect the K16 pre-crash safety city sensor connector.

    2. Select "Bus Check" on the GTS Click here.

      Result
      Result Proceed to
      "Front Camera Module" is not displayed on the GTS A
      Several ECUs and sensors in addition to "Front Camera Module" are displayed on the GTS B

    B

    CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (ENGINE STOP AND START ECU) Click here

    A

  24. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (PRE-CRASH SAFETY CITY SENSOR CAN BRANCH WIRE)


    1. A004OD6E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Pre-crash Safety City Sensor)

      Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      K16-5 (CA1P) - K16-11 (CA1N) Ignition switch off 54 to 69 Ω

    OK

    REPLACE PRE-CRASH SAFETY CITY SENSOR Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (PRE-CRASH SAFETY CITY SENSOR)

  25. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (ENGINE STOP AND START ECU)


    1. Disconnect the D139 engine stop and start ECU connector.

    2. Select "Bus Check" on the GTS Click here.

      Result
      Result Proceed to
      "Stop and Go/Start" is not displayed on the GTS A
      Several ECUs and sensors in addition to "Stop and Go/Start" are displayed on the GTS B

    B

    CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE) Click here

    A

  26. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (ENGINE STOP AND START ECU CAN BRANCH WIRE)


    1. A004SAAE02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Engine Stop and Start ECU)

      Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D139-15 (CANH) - D139-16 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE ENGINE STOP AND START ECU Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (ENGINE STOP AND START ECU)

  27. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)


    1. A004N50E02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Center Airbag Sensor Assembly)

      Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Disconnect the center airbag sensor assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D10-13 (CANH) - D10-22 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY)