CAN COMMUNICATION SYSTEM Short to B+ in CAN Bus Line

DESCRIPTION

There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.

  • Short between CAN bus lines and +B

  • ECM

  • Brake actuator assembly (skid control ECU)

  • Parking brake with bracket actuator assembly (parking brake ECU)

  • Certification ECU (smart key ECU assembly)*1

  • Power steering ECU assembly

  • Air conditioning amplifier assembly*2

  • Spiral with sensor cable sub-assembly (steering angle sensor)

  • Yaw rate sensor

  • Main body ECU (instrument panel junction block assembly)

  • Radio and display receiver assembly*3

  • Headlight swivel ECU assembly*4

  • Headlight leveling ECU assembly*5

  • Power management control ECU*1

  • Center airbag sensor assembly

  • Pre-crash safety city sensor*6

  • Engine stop and start ECU

  • Combination meter assembly

  • No. 1 junction connector

  • No. 2 junction connector

  • No. 3 junction connector

WIRING DIAGRAM

A004OTAE02
A004NU5E02
A004RCSE02
w/ Entry and Start System
*a Power Management Control ECU
*b Yaw Rate Sensor
*c Combination Meter Assembly
*d No. 3 Junction Connector
A004TBFE02
A004QJVE02
A004N3DE02

CAUTION / NOTICE / HINT

Note


  • For vehicles with an entry and start system:

    Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) Click here.

  • As the door control battery is installed between the vehicle battery and main body ECU (instrument panel junction block assembly), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (instrument panel junction block assembly) before performing this troubleshooting procedure Click here.

Tech Tips

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.


    NEXT

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.


    NEXT

  3. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)


    1. A004P7AE02
      Text in Illustration
      *a Front view of DLC3

      Disconnect the D151 No. 1 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D8-6 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D8-14 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

    OK

  4. CONNECT CONNECTOR


    1. Reconnect the D151 No. 1 junction connector.


    NEXT

  5. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR SIDE)


    1. A004P7AE02
      Text in Illustration
      *a Front view of DLC3

      Disconnect the D164 No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D8-6 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D8-14 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  6. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

    Note

    For vehicles without a radio and display type, go to "Check for Short to B+ in CAN Bus Wire (No. 3 Junction Connector - Air Conditioning Amplifier Assembly)".


    1. A004SF1E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D155-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D155-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  7. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

    Note

    For vehicles with an entry and start system, go to "Check for Short to B+ in CAN Bus Wire (No. 3 Junction Connector - Center Airbag Sensor Assembly)".


    1. A004RBJE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D156-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D156-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  8. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)


    1. A004OBTE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D157-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D157-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  9. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - CERTIFICATION ECU)

    Note

    For vehicles without an entry and start system, go to "Check for Short to B+ in CAN Bus Wire (No. 3 Junction Connector - Engine Stop and Start ECU)".


    1. A004NEWE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D158-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D158-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  10. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)


    1. A004TC2E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D160-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D160-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  11. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - ENGINE STOP AND START ECU)


    1. A004TH9E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D159-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D159-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  12. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - YAW RATE SENSOR)


    1. A004OD2E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D162-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D162-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  13. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - HEADLIGHT ECU)

    Note

    For vehicles with an entry and start system or without an entry and start system and halogen headlight, go to "Check for Short to B+ in CAN Bus Wire (No. 3 Junction Connector - Combination Meter Assembly)".


    1. A004Q54E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D163-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D163-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  14. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    1. A004RHOE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D161-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D161-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    OK

    REPLACE NO. 3 JUNCTION CONNECTOR

    NG

    CONNECT CONNECTOR Click here

  15. CONNECT CONNECTOR


    1. Reconnect the No. 3 junction connectors.


    NEXT

  16. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)


    1. A004SMEE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Radio and Display Receiver Assembly)
      *b Front view of DLC3

      Disconnect the radio and display receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D124-9 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D124-10 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    OK

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)

  17. CONNECT CONNECTOR


    1. Reconnect the No. 3 junction connectors.


    NEXT

  18. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)


    1. A004SA4E02
      Text in Illustration
      *A for Automatic Air conditioning System
      *B for Manual Air Conditioning System and w/o Air Conditioning System
      *a

      Rear view of wire harness connector

      (to Air Conditioning Amplifier Assembly)
      *b Front view of DLC3

      Disconnect the air conditioning amplifier assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for Automatic Air conditioning System
      Tester Connection Switch Condition Specified Condition
      D47-11 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D47-12 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      for Manual Air Conditioning System and w/o Air Conditioning System
      Tester Connection Switch Condition Specified Condition
      D101-11 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D101-12 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

  19. CONNECT CONNECTOR


    1. Reconnect the No. 3 junction connectors.


    NEXT

  20. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)


    1. A004NWAE02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Center Airbag Sensor Assembly)
      *b Front view of DLC3

      Disconnect the center airbag sensor assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D10-13 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D10-22 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    OK

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)

  21. CONNECT CONNECTOR


    1. Reconnect the No. 3 junction connectors.


    NEXT

  22. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CERTIFICATION ECU)


    1. A004OLKE02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Certification ECU [Smart Key ECU Assembly])
      *b Front view of DLC3

      Disconnect the certification ECU (smart key ECU assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D54-9 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D54-10 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)

  23. CONNECT CONNECTOR


    1. Reconnect the No. 3 junction connectors.


    NEXT

  24. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER MANAGEMENT CONTROL ECU)


    1. A004TV4E02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Power Management Control ECU)
      *b Front view of DLC3

      Disconnect the power management control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D111-14 (CA1H) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D111-13 (CA1L) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    OK

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (CA1H, CA1L)

  25. CONNECT CONNECTOR


    1. Reconnect the No. 3 junction connectors.


    NEXT

  26. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ENGINE STOP AND START ECU)


    1. A004N12E02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Engine Stop and Start ECU)
      *b Front view of DLC3

      Disconnect the engine stop and start ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D139-15 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D139-16 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    OK

    REPLACE ENGINE STOP AND START ECU Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO ENGINE STOP AND START ECU (CANH, CANL)

  27. CONNECT CONNECTOR


    1. Reconnect the No. 3 junction connectors.


    NEXT

  28. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR)


    1. A004NTCE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Yaw Rate Sensor)
      *b Front view of DLC3

      Disconnect the yaw rate sensor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D69-2 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D69-3 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    OK

    REPLACE YAW RATE SENSOR Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CANH, CANL)

  29. CONNECT CONNECTOR


    1. Reconnect the No. 3 junction connectors.


    NEXT

  30. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (HEADLIGHT ECU)


    1. Disconnect the headlight swivel ECU assembly*1 or headlight leveling ECU assembly*2 connector.


      • *1: w/ Adaptive Front-lighting System

      • *2: w/o Adaptive Front-lighting System

      A004TZWE02
      Text in Illustration
      *A w/ Adaptive Front-lighting System *B w/o Adaptive Front-lighting System
      *a

      Rear view of wire harness connector

      (to Headlight Swivel ECU Assembly)

      		 *b

      Front view of wire harness connector

      (to Headlight Leveling ECU Assembly)
      *c Front view of DLC3 - -

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      w/ Adaptive Front-lighting System
      Tester Connection Switch Condition Specified Condition
      A38-12 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      A38-13 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      w/o Adaptive Front-lighting System
      Tester Connection Switch Condition Specified Condition
      A82-6 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      A82-7 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      Result
      Result Proceed to
      OK (w/ Adaptive Front-lighting System) A
      OK (for LHD, w/o Adaptive Front-lighting System) B
      OK (for RHD, w/o Adaptive Front-lighting System) C
      NG D

    A

    REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY Click here

    B

    REPLACE HEADLIGHT LEVELING ECU ASSEMBLY Click here

    C

    REPLACE HEADLIGHT LEVELING ECU ASSEMBLY Click here

    D

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO HEADLIGHT ECU (CANH, CANL)

  31. CONNECT CONNECTOR


    1. Reconnect the No. 3 junction connectors.


    NEXT

  32. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)


    1. A004MX0E02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Combination Meter Assembly)
      *b Front view of DLC3

      Disconnect the combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D66-32 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D66-31 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    OK

    REPLACE COMBINATION METER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

  33. CONNECT CONNECTOR


    1. Reconnect the No. 3 junction connectors.


    NEXT

  34. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)


    1. A004NEQE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 2 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 2 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G71-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      G71-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

    OK

  35. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)


    1. A004P7AE02
      Text in Illustration
      *a Front view of DLC3

      Disconnect the G72 No. 2 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D8-6 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D8-14 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  36. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - PARKING BRAKE ECU)


    1. A004ODSE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 2 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 2 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G70-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      G70-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    OK

    REPLACE NO. 2 JUNCTION CONNECTOR

    NG

  37. CONNECT CONNECTOR


    1. Reconnect the No. 2 junction connectors.


    NEXT

  38. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (PARKING BRAKE ECU)


    1. A004R8CE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Parking Brake with Bracket Actuator Assembly [Parking Brake ECU])
      *b Front view of DLC3

      Disconnect the parking brake with bracket actuator assembly (parking brake ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      I1-11 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      I1-23 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    OK

    REPLACE PARKING BRAKE WITH BRACKET ACTUATOR ASSEMBLY (PARKING BRAKE ECU) Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO PARKING BRAKE ECU (CANH, CANL)

  39. CONNECT CONNECTOR


    1. Reconnect the No. 2 junction connectors.


    NEXT

  40. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    1. A004NR6E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 1 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 1 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D154-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D154-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

    OK

  41. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)


    1. A004SR0E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 1 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 1 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D148-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D148-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  42. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    1. A004O76E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 1 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 1 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D149-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D149-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  43. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU)


    1. A004TGEE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 1 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 1 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D150-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D150-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  44. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)


    1. A004QLPE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 1 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 1 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D152-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D152-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  45. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - PRE-CRASH SAFETY CITY SENSOR)

    Note

    For vehicles without a pre-crash safety system, go to "Check for Short to B+ in CAN Bus Wire (No. 1 Junction Connector - ECM)".


    1. A004R9CE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 1 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 1 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D153-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D153-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  46. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)


    1. A004T2LE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 1 Junction Connector)
      *b Front view of DLC3

      Disconnect the No. 1 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D147-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D147-2 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    OK

    REPLACE NO. 1 JUNCTION CONNECTOR

    NG

    CONNECT CONNECTOR Click here

  47. CONNECT CONNECTOR


    1. Reconnect the No. 1 junction connectors.


    NEXT

  48. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU)


    1. A004RJ9E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Brake Actuator Assembly [Skid Control ECU])
      *b Front view of DLC3

      Disconnect the brake actuator assembly (skid control ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A84-2 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      A84-16 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

  49. CONNECT CONNECTOR


    1. Reconnect the No. 1 junction connectors.


    NEXT

  50. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR)


    1. A004QZIE02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])
      *b Front view of DLC3

      Disconnect the spiral with sensor cable subassembly (steering angle sensor) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D167-4 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D167-3 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    OK

    REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)

  51. CONNECT CONNECTOR


    1. Reconnect the No. 1 junction connectors.


    NEXT

  52. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU)


    1. A004TOPE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Main Body ECU [Instrument Panel Junction Block Assembly])
      *b Front view of DLC3

      Disconnect the main body ECU (instrument panel junction block assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D81-15 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D81-16 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    OK

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)

  53. CONNECT CONNECTOR


    1. Reconnect the No. 1 junction connectors.


    NEXT

  54. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY)


    1. A004QNYE02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Power Steering ECU Assembly)
      *b Front view of DLC3

      Disconnect the power steering ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      D50-1 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      D50-7 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    A

    REPLACE POWER STEERING ECU ASSEMBLY Click here

    B

    REPLACE POWER STEERING ECU ASSEMBLY Click here

    C

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)

  55. CONNECT CONNECTOR


    1. Reconnect the No. 1 junction connectors.


    NEXT

  56. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (PRE-CRASH SAFETY CITY SENSOR)


    1. A004SKQE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Pre-crash Safety City Sensor)
      *b Front view of DLC3

      Disconnect the pre-crash safety city sensor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      K16-5 (CA1P) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      K16-11 (CA1N) - D8-16 (BAT) Ignition switch off 6 kΩ or higher

    OK

    REPLACE PRE-CRASH SAFETY CITY SENSOR Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO PRE-CRASH SAFETY CITY SENSOR (CA1P, CA1N)

  57. CONNECT CONNECTOR


    1. Reconnect the No. 1 junction connectors.


    NEXT

  58. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)


    1. A004QA9E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to ECM)
      *b Front view of DLC3

      Disconnect the ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A83-26 (CANH) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      A83-25 (CANL) - D8-16 (BAT) Ignition switch off 6 kΩ or higher
      Result
      Result Proceed to
      OK (for 1WW) A
      OK (for 2WW) B
      NG C

    A

    REPLACE ECM Click here

    B

    REPLACE ECM Click here

    C

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)