NAVIGATION SYSTEM, Diagnostic DTC:B1532

DTC Code DTC Name
B1532 LVDS Signal Malfunction (from Extension Module)

DESCRIPTION

The navigation ECU and the radio and display receiver assembly are connected by the LVDS communication line.

This DTC is stored when an LVDS communication error occurs between the navigation ECU and the radio and display receiver assembly.

DTC Code DTC Detection Condition Trouble Area
B1532

When one of the conditions below is met:


  • Video signal (digital) is lost.

  • Navigation ECU is/was not connected while the ignition switch is/was to ON or ACC.

  • Communication between the master unit and the navigation ECU is/was not possible when the engine is/was started.

  • Navigation ECU power source circuit

  • LVDS circuit between radio and display receiver assembly and navigation ECU

  • Navigation ECU

  • Radio and display receiver assembly

  • No. 1 navigation wire

Tech Tips


  • Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

  • The radio and display receiver assembly is the master unit.

WIRING DIAGRAM

A004O92E06

CAUTION / NOTICE / HINT

Note

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections Click here.

PROCEDURE


  1. CHECK NO. 1 NAVIGATION WIRE (NAVIGATION ECU POWER SOURCE)


    1. A004QC8E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Navigation ECU)

      Disconnect the navigation ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z22-2 (GND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      z22-1 (B+) - z22-2 (GND) Always 11 to 14 V
      z22-3 (ACC) - z22-2 (GND) Ignition switch ACC 11 to 14 V

    NG

    CHECK NO. 1 NAVIGATION WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU) Click here

    OK

  2. CHECK NO. 1 NAVIGATION WIRE (LVDS COMMUNICATION LINE)


    1. Replace the No. 1 navigation wire (LVDS communication line) Click here.

    2. Clear the DTCs Click here.

    3. Check for DTCs Click here.

      OK
      No DTCs are output.

    OK

    END (NO. 1 NAVIGATION WIRE [LVDS COMMUNICATION LINE] IS DEFECTIVE)

    NG

  3. CHECK NAVIGATION ECU


    1. Replace the navigation ECU with a known good one Click here.

    2. Clear the DTCs Click here.

    3. Check for DTCs Click here.

      OK
      No DTCs are output.

    OK

    END (NAVIGATION ECU IS DEFECTIVE)

    NG

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

  4. CHECK NO. 1 NAVIGATION WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)


    1. Disconnect the z20 radio and display receiver assembly connector.

    2. Disconnect the z22 navigation ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z20-4 (+B2) - z22-1 (B+) Always Below 1 Ω
      z20-3 (ACC2) - z22-3 (ACC) Always Below 1 Ω
      z20-8 (GND2) - z22-2 (GND) Always Below 1 Ω
      z20-4 (+B2) - Body ground Always 10 kΩ or higher
      z20-3 (ACC2) - Body ground Always 10 kΩ or higher
      z20-8 (GND2) - Body ground Always 10 kΩ or higher

    OK

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

    NG

    REPLACE NO. 1 NAVIGATION WIRE Click here