REAR BUMPER(for Sedan) REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips

A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL REAR BUMPER GUARD


    1. Attach the 21 claws to install the rear bumper guard.

    2. Install the 2 screws.

  2. INSTALL REAR BUMPER PAD LH

    Tech Tips

    When installing the rear bumper pad, heat the rear bumper cover using a heat light.

    Standard
    Item Temperature
    Rear Bumper Cover 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper cover excessively.


    1. When using a new rear bumper cover:


      1. Clean the surface of a new rear bumper cover.

      2. Using a heat light, heat the rear bumper cover surface.

    2. When reusing the rear bumper cover:


      1. Using a heat light, heat the rear bumper cover surface.

      2. Remove the double-sided tape from the rear bumper cover.

      3. Wipe off any tape adhesive residue with cleaner.

    3. A004OE2

      Install a new rear bumper pad.


      1. Remove the peeling paper from the face of a new rear bumper pad.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      2. Install the rear bumper pad as shown in the illustration.

  3. INSTALL REAR BUMPER PAD RH

    Tech Tips

    Use the same procedure described for the LH side.

  4. INSTALL FOG LIGHT ASSEMBLY LH (w/ Rear Fog Light)

    Click here

  5. INSTALL FOG LIGHT ASSEMBLY RH (w/ Rear Fog Light)

    Tech Tips

    Use the same procedure described for the LH side.

  6. INSTALL REFLEX REFLECTOR ASSEMBLY LH (w/o Rear Fog Light)


    1. Attach the guide to install the reflex reflector.

    2. Install the 2 screws.

  7. INSTALL REFLEX REFLECTOR ASSEMBLY RH (w/o Rear Fog Light)

    Tech Tips

    Use the same procedure described for the LH side.

  8. INSTALL REAR BUMPER CUSHION

    Tech Tips

    When installing the rear bumper cushion, heat the rear bumper upper cover using a heat light.

    Standard
    Item Temperature
    Rear Bumper Upper Cover 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper upper cover excessively.


    1. When using a new rear bumper upper cover:


      1. Clean the surface of a new rear bumper upper cover.

      2. Using a heat light, heat the rear bumper upper cover surface.

    2. When reusing the rear bumper upper cover:


      1. Using a heat light, heat the rear bumper upper cover surface.

      2. Remove the double-sided tape from the rear bumper upper cover.

      3. Wipe off any tape adhesive residue with cleaner.

    3. A004PKH

      Install a new rear bumper cushion.


      1. Remove the peeling paper from the face of a new rear bumper cushion.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      2. Install the rear bumper cushion as shown in the illustration.

  9. INSTALL REAR BUMPER UPPER COVER RH


    1. Install the rear bumper upper cover with the 2 screws.

  10. INSTALL NO. 3 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

    Click here

  11. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

    Click here

  12. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

    Click here

  13. INSTALL ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)

    Click here

  14. INSTALL ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)

    Click here

  15. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

    Click here

  16. INSTALL NO. 2 FRAME WIRE (w/ Rear Fog Light)


    1. for LHD, w/ TOYOTA Parking Assist-sensor System:


      1. Attach the 3 clamps to install the No. 2 frame wire.

      2. Connect the 4 ultrasonic sensor connectors and rear fog light connector.

    2. for LHD, w/o TOYOTA Parking Assist-sensor System:


      1. Attach the 5 clamps to install the No. 2 frame wire.

      2. Connect the rear fog light connector.

    3. for RHD, w/ TOYOTA Parking Assist-sensor System:


      1. Attach the 4 clamps to install the No. 2 frame wire.

      2. Connect the 4 ultrasonic sensor connectors and rear fog light connector.

    4. for RHD, w/o TOYOTA Parking Assist-sensor System:


      1. Attach the 4 clamps to install the No. 2 frame wire.

      2. Connect the rear fog light connector.