REAR DOOR WINDOW FRAME MOULDING(for Sedan) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedures for the RH side and LH side.

  • The procedures listed below are for the LH side.

  • When installing the rear door window frame moulding, heat the vehicle body and rear door window frame moulding using a heat light.

Standard
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Rear Door Window Frame Moulding 20 to 30°C (68 to 86°F)

Note

Do not heat the vehicle body and rear door window frame moulding excessively.

PROCEDURE


  1. INSTALL REAR DOOR MOULDING SUB-ASSEMBLY OUTSIDE LH


    1. Install a nose piece to an air riveter or hand riveter.

    2. Insert the mandrel part of a new rivet into the nose piece.

    3. Using the riveter, install the rear door moulding outside as shown in the illustration.

      Tech Tips

      If the rivet cannot be cut, pull it once and cut it.

      A004SNH

      Note


      • A004RW4E67
        *1 INCORRECT
        *2 Riveter
        *3 Mandrel
        *4 CORRECT

      • Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      • A004RNQE02
        *1 Riveter
        *2 INCORRECT
        *3 CORRECT

        Confirm that the rivets are seated properly against the rear door moulding outside.

      • Do not tilt the riveter when installing the rivet to the rear door moulding outside.

      • Do not leave any space between the rivet head and rear door moulding outside.

      • A004PZTE02
        *1 Riveter
        *2 INCORRECT
        *3 CORRECT

        Do not leave any space between the rear door moulding outside and door frame. Firmly hold together the 2 items while installing the rivet.

  2. INSTALL REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY LH


    1. Clean the vehicle body surface.


      1. Using a heat light, heat the vehicle body surface.

      2. Remove the double-sided tape and butyl tape from the vehicle body surface.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Install a new rear door window frame moulding.


      1. Using a heat light, heat a new rear door window frame moulding and the vehicle body surface.

      2. Remove the peeling paper from the face of the rear door window frame moulding.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      3. A004NSRE01
        Text in Illustration
        *1 Double-sided Tape
        *2 Butyl Tape

        Attach the clip, double-sided tape and butyl tape to install the rear door window frame moulding.

        Tech Tips

        Press the rear door window frame moulding firmly to install it.

  3. INSTALL REAR DOOR WEATHERSTRIP LH


    1. Clean the door surface.


      1. Wipe off any tape adhesive residue with cleaner.

    2. If reusing the rear door weatherstrip:

      Clean the rear door weatherstrip.


      1. Remove the double-sided tape from the rear door weatherstrip.

      2. Wipe off any tape adhesive residue with cleaner.

      3. A004OGAE01
        Standard
        Area Specified Condition
        *1 Length: 30 mm (1.18 in.)
        *2 Width: 5.0 mm (0.197 in.)
        *3 Thickness: 0.8 mm (0.0315 in.)

        Apply new double-sided tape to the rear door weatherstrip, as shown in the illustration.

        Standard
        Area Specified Condition
        *1 Length: 30 mm (1.18 in.)
        *2 Width: 5.0 mm (0.197 in.)
        *3 Thickness: 0.8 mm (0.0315 in.)
    3. A004UDL
      Area Specified Condition
      *1 Length: 30 mm (1.18 in.)
      *2 Width: 5.0 mm (0.197 in.)
      *3 Thickness: 0.8 mm (0.0315 in.)

      Install the rear door weatherstrip.


      1. Using a heat light, heat the door surface.

      2. Remove the peeling paper from the face of the weatherstrip.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      3. Attach the 3 clips to install the upper part of the rear door weatherstrip.

  4. INSTALL REAR DOOR FRAME GARNISH LH

    Click here

  5. INSTALL REAR DOOR BELT MOULDING LH

    Click here

  6. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

    Click here

  7. INSTALL REAR DOOR QUARTER WINDOW GLASS LH

    Click here

  8. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

    Click here

  9. INSTALL REAR DOOR GLASS RUN LH

    Click here

  10. INSTALL REAR DOOR SERVICE HOLE COVER LH

    Click here

  11. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

    Click here

  12. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  13. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window)

    Click here

  14. INSTALL DOOR ASSIST GRIP COVER LH

    Click here

  15. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

    Click here

  16. INSTALL REAR DOOR NO. 1 STIFFENER CUSHION

    Click here

  17. INSTALL REAR DOOR REGULATOR INSIDE HANDLE PLATE (w/o Power Window)

    Click here

  18. INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

    Click here

  19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Power Window)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.