FRONT LOWER SUSPENSION ARM INSTALLATION

PROCEDURE


  1. TEMPORARILY INSTALL FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY LH


    1. Position the front suspension crossmember on a level surface.

    2. A004SJX

      Temporarily install the front lower suspension arm LH to the front suspension crossmember with the 2 bolts and nut.

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut fixed in place.

  2. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

    A004RX0

    1. Support the front suspension crossmember with a transmission jack.

    2. Install the front suspension crossmember and 4 front suspension member mounting stoppers with the 4 bolts and 2 nuts, and tighten the bolts and nuts in several steps while alternately inserting SST into the left and right reference holes of the front suspension crossmember.

      A004O5FE01
      *1 Front
      *2 CORRECT
      *3 INCORRECT
      SST
      09670-00020
      Torque:
      for bolt A
      137 N*m  { 1397 kgf*cm, 101 ft.*lbf }
      for bolt B and nut B
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }
    3. A004OG8

      Attach the 2 clamps and claw to connect the oxygen sensor wire to the front suspension crossmember.

  3. INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH


    1. A004SLPE07

      Install the rear brace with the 3 bolts.

      Torque:
      for bolt A
      137 N*m  { 1397 kgf*cm, 101 ft.*lbf }
      for bolt B
      93 N*m  { 948 kgf*cm, 69 ft.*lbf }

  4. INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH

    Tech Tips

    Perform the same procedure as for the LH side.

  5. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH


    1. A004OJRE01

      Install the reinforcement with the 4 bolts.

      Torque:
      99 N*m  { 1010 kgf*cm, 73 ft.*lbf }

      Note

      Tighten the bolts in the order of C, B, D and A.

  6. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH


    1. A004PDSE01

      Install the reinforcement with the 4 bolts.

      Torque:
      99 N*m  { 1010 kgf*cm, 73 ft.*lbf }

      Note

      Tighten the bolts in the order of C, B, D and A.

  7. CONNECT FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY LH

    Click here

  8. CONNECT FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY RH

    Tech Tips

    Perform the same procedure as the LH side.

  9. CONNECT TIE ROD END SUB-ASSEMBLY LH

    Click here

  10. CONNECT TIE ROD END SUB-ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  11. CONNECT FRONT STABILIZER LINK ASSEMBLY LH


    1. A004OBI

      Connect the front stabilizer link to the front stabilizer bar with the nut.

      Torque:
      74 N*m  { 755 kgf*cm, 55 ft.*lbf }

      Tech Tips

      If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.

  12. CONNECT FRONT STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  13. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

    Click here

  14. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

    Click here

  15. INSTALL COLUMN HOLE COVER SILENCER SHEET

    Click here

  16. INSTALL REAR ENGINE UNDER COVER LH


    1. Install the under cover with the 5 clips.

  17. INSTALL REAR ENGINE UNDER COVER RH

    Tech Tips

    Perform the same procedure as for the LH side.

  18. INSTALL FRONT WHEELS

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  19. STABILIZE SUSPENSION


    1. Lower the vehicle.

    2. Bounce the vehicle up and down at the corners several times to stabilize the suspension.

  20. INSTALL CENTER NO. 4 ENGINE UNDER COVER

    Click here

  21. INSTALL NO. 1 ENGINE UNDER COVER

    Click here

  22. INSTALL FRONT BUMPER ABSORBER LOWER COVER

    Click here

  23. TIGHTEN FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY LH


    1. A004OVCE01
      *1 Fulcrum Length
      *2 Turn

      Using SST, tighten bolt A.

      SST
      09961-01270
      Torque:
      without SST
      233 N*m  { 2376 kgf*cm, 172 ft.*lbf }
      with SST
      172 N*m  { 1755 kgf*cm, 127 ft.*lbf }

      Note


      • Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut fixed in place.

      • Use a torque wrench with a fulcrum length of 425 mm (1.39 ft.).

      • This torque value is effective when SST is parallel to the torque wrench.

      • The final torque must be applied under standard vehicle height conditions.

    2. Tighten bolt B.

      Torque:
      214 N*m  { 2182 kgf*cm, 158 ft.*lbf }

  24. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT


    1. Inspect and adjust the front wheel alignment Click here.

  25. ADJUST HEADLIGHT ASSEMBLY


    1. for Halogen Headlight:

      Adjust the headlight assembly Click here.

    2. for LED Headlight:

      Adjust the headlight assembly Click here.