FRONT AXLE HUB INSTALLATION

PROCEDURE

INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH
1. Hold the front axle assembly in a vise between aluminum plates.
  
  Note
  
  When using a vise, do not overtighten it.
2. Install the front brake dust cover to the steering knuckle.
3. Install the front axle hub sub-assembly with the 4 bolts.
  
  Torque:
  
  96 N*m { 979 kgf*cm, 71 ft.*lbf }
  
  Note
  
  Do not place the magnet rotor side of the hub bearing so that it is facing downward, and do not allow the magnet rotor side to become damaged or contact foreign matter.
INSTALL FRONT AXLE ASSEMBLY LH
1. Text in Illustration
  
  *1 Matchmark
  
  Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.
2. Install the front axle assembly to the front shock absorber assembly with coil spring with the 2 bolts and 2 nuts.
  
  Torque:
  
  240 N*m { 2447 kgf*cm, 177 ft.*lbf }
  
  Note
  
  Be careful not to damage the drive shaft boot or the magnet rotor of the hub and bearing.
CONNECT FRONT NO. 1 SUSPENSION LOWER ARM SUB-ASSEMBLY LH
1. Connect the suspension lower arm to the front lower ball joint with the bolt and 2 nuts.
  
  Torque:
  
  89 N*m { 908 kgf*cm, 66 ft.*lbf }
CONNECT TIE ROD END SUB-ASSEMBLY LH

Click here
INSTALL FRONT DISC
1. Text in Illustration
  
  *1 Matchmark
  
  Align the matchmarks of the disc and axle hub and install the disc.
INSTALL DISC BRAKE CYLINDER ASSEMBLY LH
1. Install the front disc brake cylinder assembly to the steering knuckle with the 2 bolts.
  
  Torque:
  
  107 N*m { 1089 kgf*cm, 79 ft.*lbf }
TEMPORARILY INSTALL FRONT AXLE SHAFT NUT LH
1. Clean the threaded parts on the drive shaft and a new axle shaft nut using a non-residue solvent.
  Note
  - Be sure to perform this work for a new drive shaft.
  - Keep the threaded parts free of oil and foreign objects.
2. Using a 30 mm socket wrench, temporarily install the axle shaft nut.
  
  Torque:
  
  292 N*m { 2978 kgf*cm, 215 ft.*lbf }
  
  Tech Tips
  
  Stake the nut after inspecting for looseness and runout in the following steps.
REMOVE DISC BRAKE CYLINDER ASSEMBLY LH
REMOVE FRONT DISC
INSPECT FRONT AXLE HUB BEARING LOOSENESS

Click here
INSPECT FRONT AXLE HUB RUNOUT

Click here
INSTALL FRONT DISC
1. Text in Illustration
  
  *1 Matchmark
  
  Align the matchmarks of the disc and axle hub and install the disc.
  
  Note
  
  When replacing the disc with a new one, select the installation position where the front disc has the smallest runout.
INSTALL DISC BRAKE CYLINDER ASSEMBLY LH
1. Install the front disc brake cylinder assembly to the steering knuckle with the 2 bolts.
  
  Torque:
  
  107 N*m { 1089 kgf*cm, 79 ft.*lbf }
INSTALL FRONT FLEXIBLE HOSE
1. Install the front flexible hose to the steering knuckle with the bolt.
  
  Torque:
  
  29 N*m { 296 kgf*cm, 21 ft.*lbf }
INSTALL FRONT SPEED SENSOR LH
1. Install the front speed sensor wire and front flexible hose to the front shock absorber with the bolt, and attach the clamp.
  
  Torque:
  
  29 N*m { 296 kgf*cm, 21 ft.*lbf }
  
  Tech Tips
  
  Install the front flexible hose first and then the speed sensor wire bracket.
  
  Note
  
  Do not twist the front speed sensor when installing it.
2. Install the front speed sensor to the steering knuckle with the bolt.
  
  Torque:
  
  8.5 N*m { 87 kgf*cm, 76 in.*lbf }
  
  Note
  
  Do not twist the front speed sensor wire when installing the front speed sensor.
STAKE FRONT AXLE SHAFT NUT LH
1. Using a chisel and a hammer, stake the front axle shaft nut.
INSTALL FRONT WHEEL

Torque:

103 N*m { 1050 kgf*cm, 76 ft.*lbf }
INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Click here
CHECK SPEED SENSOR SIGNAL

Click here