TRANSMISSION CONTROL CABLE INSTALLATION

PROCEDURE


  1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


    1. A004N6V

      Install the control cable assembly through the floor hole.

    2. Attach the 2 claws to connect the shift control cable and select control cable to the floor shift lever assembly.

    3. A004N8M

      Attach the grommet of the control cable assembly with the 2 nuts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    4. A004OZ1

      Connect the end of the shift control cable to the shift lever assembly and install the clip.

    5. A004RN0

      Attach the bracket of the control cable assembly with the bolt.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    6. A004UCR

      Connect the 2 cables to the control cable bracket with 2 new clips.

    7. A004OIS

      Connect the 2 cables to the transaxle and install the 2 clips.

    8. Release the lock of the cable length adjustment structure of the select cable.


      1. A004RNBE01
        *1 Twist
        *2 Stopper

        Twist the stopper.

      2. A004NMOE04
        *1 Pull out
        *2 Lock Piece
        *3 Case

        Pull the lock piece outward from the case to release the lock.

    9. A004NRME01

      Pressing the shift and select lever shaft (*1) and pin (*2), push in pin (*3) and check that the shift and select lever shaft is secured at the 1st-2nd gear selected position (the shaft comes to a stop at the position 8 mm (0.315 in.) below the N position).

    10. A004S38

      Connect the end of the select control cable to the shift lever assembly and install the clip.

      Note


      • Make sure the lock piece of the select control cable is facing upward when the select control cable is connected.

      • Make sure the clip is inserted in the direction shown in the illustration.

    11. A004MWPE02
      Text in Illustration
      *1 Slider
      *2 Inhibitor Wall

      Push the slider against the inhibitor wall.

      Note


      • Do not pull up the slider.

      • When adjusting the cable, make sure that the shift lever is not in 1 or 2.

    12. Lock the cable length adjustment structure of the select cable.


      1. A004O2XE03
        *1 Push
        *2 Lock Piece
        *3 Case

        Push the lock piece into the case with slider held against the inhibitor wall.

      2. A004NXIE01
        *1 Return
        *2 Stopper

        Return the stopper to prevent the lock from being released.

        Note


        • Push in the lock piece completely.

        • Make sure the cable length adjustment structure is locked securely.

    13. A004Q9AE01
      *1 Pull

      Release the pin that fixes the transmission outer lever.


      1. Pull the pin toward the left front side of the vehicle.

  2. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

    A004RCG

    1. Install the front No. 1 floor heat insulator with the 3 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  3. INSTALL CONSOLE BOX ASSEMBLY

    Click here

  4. INSTALL AIR CLEANER CASE

    Click here

  5. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

  6. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

    Click here

  7. INSTALL BATTERY CARRIER

    Click here

  8. INSTALL BATTERY TRAY

  9. INSTALL BATTERY

  10. INSTALL BATTERY CLAMP SUB-ASSEMBLY

    Click here

  11. INSTALL NO. 1 ENGINE COVER

    Click here

  12. INSTALL RADIATOR SUPPORT OPENING COVER

    Click here

  13. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    1. Install the front exhaust pipe assembly Click here.