STOP AND START SYSTEM, Diagnostic DTC:P0562

DTC Code DTC Name
P0562 System Voltage Low

DESCRIPTION

The engine stop and start ECU monitors +B terminal voltage while the engine is stopped by stop and start control. If the voltage drops below the specified level, the engine stop and start ECU stores DTC P0562 and blinks the stop and start cancel indicator light.

DTC No. DTC Detection Condition Trouble Area
P0562

Both of the following conditions continue for 2 seconds or more (1 trip detection logic):


  • +B terminal voltage is 9 V or less.

  • During engine stop by stop and start control.

  • Battery

  • Wire harness or connector

  • EFI MAIN relay

  • Engine stop and start ECU

CONFIRMATION DRIVING PATTERN

Tech Tips

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs Click here.


  1. CONFIRMATION AFTER TROUBLESHOOTING

    Tech Tips


    • If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.

    • Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs Click here.

    4. Start the engine and warm it up.

    5. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    6. Stop the vehicle, move the shift lever to neutral and release the clutch pedal.

    7. Keep the engine stopped by stop and start control for 1 second or more.

    8. Depress the clutch pedal and start the engine.

      Tech Tips

      If the engine cranks slowly when the engine is restarted, it can be determined that battery voltage is low.

    9. Check that DTCs are not output Click here.

  2. STOP AND START SYSTEM OPERATION CHECK

    Tech Tips

    If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.


    1. Start the engine and warm it up.

    2. Turn the air conditioning system off.

    3. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    4. Stop the vehicle, move the shift lever to neutral and release the clutch pedal.

    5. Allow the engine to stop by stop and start control.

    6. Depress the clutch pedal and start the engine.

WIRING DIAGRAM

A004OC6E02

CAUTION / NOTICE / HINT

Note


  • Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU Click here.

  • After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU Click here.

  • After replacing the engine stop and start ECU or yaw rate sensor, perform deceleration sensor zero point clear and calibration Click here.

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting Click here.

PROCEDURE


  1. READ VALUE USING GTS (BATTERY VOLTAGE)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

      Tech Tips

      Do not start the engine.

    3. Turn the GTS on.

    4. Turn off all electrical systems.

    5. Enter the following menus: Powertrain / Stop and Start / Data List / Battery Voltage.

    6. Read the battery voltage displayed on the GTS screen.

      Result
      Result Proceed to
      Below 9 V A
      9 to 14 V (for 1WW) B
      9 to 14 V (for 2WW) C

    B

    CHECK BATTERY Click here

    C

    CHECK BATTERY Click here

    A

  2. INSPECT RELAY (EFI MAIN RELAY)


    1. Inspect the EFI MAIN relay.



    NG

    REPLACE RELAY (EFI MAIN RELAY)

    OK

  3. CHECK HARNESS AND CONNECTOR (+B TERMINAL VOLTAGE)


    1. Turn the ignition switch to ON.

      A004U0AE02
      Text in Illustration
      *a

      Component with harness connected

      (Engine Stop and Start ECU)

      		 - -

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      A79-5 (+B) - Body ground Ignition switch ON 9.5 to 14 V

    OK

    REPLACE ENGINE STOP AND START ECU Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND START ECU - EFI MAIN RELAY)