MONOLITHIC CONVERTER INSTALLATION

PROCEDURE

1. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

   
   

   1. 

      Temporarily install the manifold stay with the 2 nuts.

   2. 

      Text in Illustration

      *1	Turbocharger Sub-assembly
      *2	Gasket
      *3	V-band Clamp
      *4	Exhaust Manifold Converter Sub-assembly

      Temporarily install the exhaust manifold converter sub-assembly and engine bracket with the 3 nuts, 3 bolts, new V-band clamp and new gasket.

   3. Tighten the engine bracket with the 3 bolts.

      Torque:

      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

   4. 

      Temporarily install the manifold stay with the 2 bolts.

   5. 

      Text in Illustration

      *1	V-band Clamp

      Align the V-band clamp as shown in the illustration and temporarily install it.

      Torque:

      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

      Tech Tips

      To prevent the V-band clamp from interfering with the No. 1 manifold converter insulator, temporarily install the V-band clamp at the angle shown in the illustration.

   6. Tighten the 5 nuts, 2 bolts, V-band clamp and exhaust manifold converter sub-assembly in the order shown in the illustration.

      

      Torque:

      for bolt

      38 N*m  { 387 kgf*cm, 28 ft.*lbf }

      for nut

      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

      for V-band clamp

      15 N*m  { 153 kgf*cm, 11 ft.*lbf }

2. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

   
   

   1. Install the No. 1 exhaust manifold heat insulator with the 2 bolts.

      Torque:

      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

   2. Attach the 2 clamps and connect the engine wire.

3. INSTALL FRONT EXHAUST PIPE ASSEMBLY

   
   

   1. Check the free length of the compression spring.

      
      

      1. 

         Using a vernier caliper, measure the free length of the compression spring.

         Minimum length
         41.5 mm (1.63 in.)

         If the free length is less than the minimum, replace the compression spring.

   2. 

      Text in Illustration

      *1	Exhaust Manifold Converter Sub-assembly
      *2	Gasket
      *a	Wooden Block

      Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the exhaust manifold converter sub-assembly.

      Note

      
      

      • Be sure to install the gasket so that it faces the correct direction.

      • Do not reuse the gasket.

      • Do not damage the gasket.

      • When connecting the exhaust pipe, do not push in the gasket with the exhaust pipe.

   3. Install a new gasket to the front exhaust pipe assembly.

   4. Connect the front exhaust pipe assembly to the 2 exhaust pipe supports.

   5. Install the front exhaust pipe assembly with the 4 bolts and 4 compression springs.

      Torque:

      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

4. INSTALL FRONT FLOOR CENTER BRACE

   Click here

5. INSTALL NO. 2 ENGINE UNDER COVER

   Click here

6. INSTALL OUTER COWL TOP PANEL

   Click here

7. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY

   Click here

8. INSTALL DIFFERENTIAL PRESSURE SENSOR

   Click here

9. INSTALL EXHAUST GAS TEMPERATURE SENSOR

   
   

   • for Sensor 1: Click here

   • for Sensor 2: Click here

10. INSTALL AIR FUEL RATIO SENSOR

    
    

    • for Sensor 1: Click here

    • for Sensor 2: Click here

11. INSPECT FOR EXHAUST GAS LEAK

    Click here

12. PERFORM INITIALIZATION

    
    

    • Perform DPF history information reset Click here.

    • Perform NOx storage catalyst learning value reset Click here.