STEERING GEAR INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. INSTALL TIE ROD END SUB-ASSEMBLY LH


    1. A004PNYE04
      Text in Illustration
      *1 Matchmark

      Install the lock nut and tie rod end to the steering gear so that the matchmarks align.

      Tech Tips

      After adjusting toe-in, tighten the lock nut to the specified torque.

  2. INSTALL TIE ROD END SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  3. INSTALL STEERING LINK ASSEMBLY


    1. A004QPB

      Install the steering link to the front suspension crossmember with the 2 bolts and 2 nuts.

      Torque:
      110 N*m  { 1122 kgf*cm, 81 ft.*lbf }

      Note


      • Make sure to tighten the bolts starting from the left side of the vehicle.

      • Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut fixed in place.

  4. INSTALL STEERING INTERMEDIATE SHAFT


    1. A004NRGE10
      Text in Illustration
      *1 Matchmark

      Align the matchmarks and install the steering intermediate shaft to the steering link.

    2. Install a new bolt.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

  5. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    1. A004OG9

      Align the round hole in the No. 1 steering column hole cover with the protrusion of the steering link and install the cover.

  6. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

    Click here

  7. INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH

    Click here

  8. INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH

    Click here

  9. INSTALL FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY LH

    Click here

  10. INSTALL FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY RH

    Click here

  11. CONNECT TIE ROD END SUB-ASSEMBLY LH


    1. A004NG8

      Connect the tie rod end to the steering knuckle with the nut.

      Torque:
      49 N*m  { 500 kgf*cm, 36 ft.*lbf }

      Note

      Tighten the nut up to an additional 60° if the holes for the cotter pin are not aligned.

    2. Install a new cotter pin.

  12. CONNECT TIE ROD END SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  13. INSTALL FRONT STABILIZER LINK ASSEMBLY LH

    Click here

  14. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  15. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

    Click here

  16. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

    Click here

  17. INSTALL REAR ENGINE UNDER COVER LH

    Click here

  18. INSTALL REAR ENGINE UNDER COVER RH

    Click here

  19. INSTALL NO. 4 CENTER ENGINE UNDER COVER

    Click here

  20. INSTALL NO. 2 ENGINE UNDER COVER

    Click here

  21. INSTALL NO. 1 ENGINE UNDER COVER

  22. INSTALL FRONT LOWER BUMPER ABSORBER

    Click here

  23. CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    1. A004SM0E02
      Text in Illustration
      *1 Lip
      *2 Clip B
      *3 Clip A
      *4 Lip

      Attach clip B to the body and install the No. 1 steering column hole cover to the body with clip A.

      Note

      Make sure that the lip of the No. 1 steering column hole cover is not damaged.

  24. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

    Click here

  25. INSTALL COLUMN HOLE COVER SILENCER SHEET

    Click here

  26. INSTALL FRONT WHEELS

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  27. ADJUST FRONT WHEEL ALIGNMENT

    Click here