REAR DOOR WINDOW FRAME MOULDING(for Wagon) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedures for the RH side and LH side.

  • The procedures listed below are for the LH side.

  • When installing the rear door window frame moulding sub-assembly, heat the vehicle body and rear door window frame moulding sub-assembly using a heat light.

Standard
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Rear Door Window Frame Moulding Sub-assembly 20 to 30°C (68 to 86°F)

Note

Do not heat the vehicle body and rear door window frame moulding sub-assembly excessively.

PROCEDURE


  1. INSTALL REAR DOOR REAR WINDOW FRAME MOULDING LH


    1. Install a nose piece to an air riveter or hand riveter.

    2. Insert the mandrel part of a new rivet into the nose piece.

    3. Using the riveter, install the rear door rear window frame moulding as shown in the illustration.

      Tech Tips

      If the rivet cannot be cut, pull it once and cut it.

      A005459

      Note


      • B0040FUE02
        *1 INCORRECT
        *2 Riveter
        *3 Mandrel
        *4 CORRECT

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      • A0052Y4E02
        *1 Riveter
        *2 INCORRECT
        *3 CORRECT

        Confirm that the rivets are seated properly against the rear door rear window frame moulding.

      • Do not tilt the riveter when installing the rivet to the rear door rear window frame moulding.

      • Do not leave any space between the rivet head and rear door rear window frame moulding.

      • A0053AHE02
        *1 Riveter
        *2 INCORRECT
        *3 CORRECT

        Do not leave any space between the rear door rear window frame moulding and door frame. Firmly hold together the 2 items while installing the rivet.

  2. INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING LH


    1. Install a nose piece to an air riveter or hand riveter.

    2. Insert the mandrel part of a new rivet into the nose piece.

    3. Using the riveter, install the rear door upper window frame moulding as shown in the illustration.

      Tech Tips

      If the rivet cannot be cut, pull it once and cut it.

      A00537J

      Note


      • B0040FUE67
        *1 INCORRECT
        *2 Riveter
        *3 Mandrel
        *4 CORRECT

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      • A0052Y4E02
        *1 Riveter
        *2 INCORRECT
        *3 CORRECT

        Confirm that the rivets are seated properly against the rear door upper window frame moulding.

      • Do not tilt the riveter when installing the rivet to the rear door upper window frame moulding.

      • Do not leave any space between the rivet head and rear door upper window frame moulding.

      • A0053AHE02
        *1 Riveter
        *2 INCORRECT
        *3 CORRECT

        Do not leave any space between the rear door upper window frame moulding and door frame. Firmly hold together the 2 items while installing the rivet.

  3. INSTALL REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY LH

    Click here

  4. INSTALL REAR DOOR WEATHERSTRIP LH

    A0059JU

    1. Attach the 2 clips to install the upper part of the rear door weatherstrip.

  5. INSTALL REAR DOOR FRAME GARNISH LH

    Click here

  6. INSTALL REAR DOOR BELT MOULDING LH

    Click here

  7. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

    Click here

  8. INSTALL REAR DOOR QUARTER WINDOW GLASS LH

    Click here

  9. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

    Click here

  10. INSTALL REAR DOOR GLASS RUN LH

    Click here

  11. INSTALL REAR DOOR SERVICE HOLE COVER LH

    Click here

  12. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

    Click here

  13. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  14. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window)

    Click here

  15. INSTALL DOOR ASSIST GRIP COVER LH

    Click here

  16. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

    Click here

  17. INSTALL REAR DOOR NO. 1 STIFFENER CUSHION

    Click here

  18. INSTALL REAR DOOR REGULATOR INSIDE HANDLE PLATE (w/o Power Window)

    Click here

  19. INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

    Click here

  20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Power Window)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.