WIPER AND WASHER SYSTEM(w/ Rain Sensor) Wiper and Washer Switch Circuit

DESCRIPTION

This circuit provides power to operate the windshield wiper switch. The manual operation signals are sent to the windshield wiper relay.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

PROCEDURE

1. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - BATTERY)

   
   
   1. 

      Text in Illustration

      *1	Front view of wire harness connector (to Windshield Wiper Switch)

      Disconnect the D33 switch connector.

   2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition D33-2 (+B) - Body ground Ignition switch ON 11 to 14 V

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

2. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY

   
   
   1. 

      Text in Illustration

      *1	Component without harness connected (Windshield Wiper Switch)

      Remove the windshield wiper switch Click here.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition A-3 (+1) - A-1 (+S) Front wiper switch off Below 1 Ω A-3 (+1) - A-2 (+B) Front wiper switch MIST Front wiper switch LO A-2 (+B) -A-4 (+2) Front wiper switch HI A-9 (AUTO) - A-10 (E) Front wiper switch AUTO A-8 (VR2) - A-7 (VR1) Adjusting ring* changed from (+) side to (-) side Below 10 Ω to 2700 Ω B-2 (EW) - B-3 (WF) Front washer switch on Below 1 Ω Front washer switch off 10 kΩ or higher

      Tech Tips

      *: The rain sensor sensitivity can be adjusted by the windshield wiper switch adjusting ring.

   
   

   NG

   REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY Click here

   OK

3. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - FRONT WIPER MOTOR)

   
   
   1. 

      Text in Illustration

      *1	Front view of wire harness connector (to Front Wiper Motor)
      *2	Front view of wire harness connector (to Windshield Wiper Switch)

      Disconnect the A9 motor connector.

   2. Disconnect the D33 switch connector.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD Tester Connection Condition Specified Condition D33-2 (+B) - A9-4 Always Below 1 Ω D33-3 (+1) - A9-3 D33-4 (+2) - A9-2 D33-2 (+B) - Body ground Always 10 kΩ or higher D33-3 (+1) - Body ground
      for RHD Tester Connection Condition Specified Condition D33-2 (+B) - A9-5 Always Below 1 Ω D33-3 (+1) - A9-2 D33-4 (+2) - A9-1 D33-2 (+B) - Body ground Always 10 kΩ or higher D33-3 (+1) - Body ground

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

4. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - WINDSHIELD WIPER RELAY AND BODY GROUND)

   
   

   1. Disconnect the D34 and D33 switch connectors.

      

   2. Disconnect the D60 relay connector.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition D33-4 (+2) - D60-11 (+2) Always Below 1 Ω D33-4 (+2) - Body ground Always 10 kΩ or higher D33-1 (+S) - D60-10 (+1) Always Below 1 Ω D33-1 (+S) - Body ground Always 10 kΩ or higher D33-9 (AUTO) - D60-3 (C1) Always Below 1 Ω D33-9 (AUTO) - Body ground Always 10 kΩ or higher D33-10 (E) - D60-15 (CO) Always Below 1 Ω D33-10 (E) - Body ground Always 10 kΩ or higher D34-3 (WF) - D60-25 (W) Always Below 1 Ω D34-3 (WF) - Body ground Always 10 kΩ or higher D33-8 (VR2) - D60-8 (VR2) Always Below 1 Ω D33-8 (VR2) - Body ground Always 10 kΩ or higher D33-7 (VR1) - D60-21 (VR1) Always Below 1 Ω D33-7 (VR1) - Body ground Always 10 kΩ or higher D34-2 (EW) - Body ground Always Below 1 Ω

      Text in Illustration

      *1

      Front view of wire harness connector (to Windshield Wiper Switch)

      *2

      Front view of wire harness connector (to Windshield Wiper Relay)

   
   

   OK

   PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR