FRONT DOOR REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A005691

      Using moulding remover A, detach the 3 claws and remove the bezel plug.

  4. REMOVE ASSIST GRIP COVER LH


    1. A0054EL

      Using moulding remover A, detach the 9 claws and remove the assist grip cover.

  5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A0056IJE02
      *1 w/ Rear Door Power Window:
      *2 w/o Rear Door Power Window:

      Using moulding remover A, detach the clip and 7 claws and remove the power window regulator master switch assembly with front door armrest base panel.

    2. Disconnect the connector and remove the power window regulator master switch.

  6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

    Tech Tips

    Use the same procedure described for the driver side.

  7. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side)

    Click here

  8. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

    Click here

  9. REMOVE FRONT DOOR NO. 1 STIFFENER CUSHION


    1. Remove the front door No. 1 stiffener cushion.

  10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A0054YL

      Remove the 3 screws.

    2. Remove the 10 clips and 2 claws.

    3. Disconnect the courtesy light connector.

    4. A0054C5E02
      Text in Illustration
      *1 Reference Boss

      Pull out the front door trim board in the direction indicated by the arrow in the illustration to detach the 5 claws of the front inner door glass weatherstrip and remove the reference boss together with the trim board.

    5. Remove the reference boss from the front door trim board.

    6. for Power Seat:


      1. A0052GL

        Detach the wire harness.

      2. A0055V0

        Disconnect the connector.

      3. Disconnect the 2 cables from the inside handle.

    7. A0056RB

      for Manual Seat:

      Disconnect the 2 cables from the inside handle.

  11. REMOVE COURTESY LIGHT ASSEMBLY

    Click here

  12. REMOVE SEAT MEMORY SWITCH (for Power Seat)


    1. A00530X

      Detach the 2 claws and remove the seat memory switch from the door trim board.

  13. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    1. A00589O

      Detach the 8 claws and remove the inside handle sub-assembly from the door trim board.

  14. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH


    1. A0055D4

      Detach the 4 claws by pulling the weatherstrip upward in the direction indicated by the arrow in the illustration to remove the weatherstrip.

  15. REMOVE DOOR FRAME GARNISH LH


    1. A0054B3

      Using a clip remover, remove the 2 clips and frame garnish.

  16. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

    Click here

  17. REMOVE NO. 2 SIDE AIR BAG SENSOR ASSEMBLY

    Click here

  18. REMOVE OUTER MIRROR INSTALL HOLE COVER LH


    1. A00552R

      Detach the 7 claws and remove the install hole cover.

  19. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

    Click here

  20. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    1. A0054Z8

      for Power Seat:

      Using a clip remover, remove the 3 clamps.

    2. A00561H

      for Manual Seat:

      Using a clip remover, remove the 2 clamps.

    3. Disconnect the 3 connectors and remove the service hole cover.

      Tech Tips

      Remove the remaining tape on the door.

  21. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. Connect the connector to the front door window regulator assembly.

    2. for Driver Side:

      Temporarily install the master switch assembly.

    3. for Front Passenger Side:

      Temporarily install the regulator switch assembly.

    4. Connect the cable to the negative (-) battery terminal.

    5. Move the door glass until the bolts appear in the service holes.

    6. Disconnect the cable from the negative (-) battery terminal.

      Note


      • w/ Navigation System (for HDD):

        After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    7. A0057ED

      Remove the 2 bolts.

      Note

      Be careful when removing the bolts as the glass may fall and become damaged.

    8. A0054KJ

      Remove the door glass in the direction indicated by the arrows in the illustration.

      Tech Tips

      Remove the glass upward.

      Note

      Be careful not to damage the glass.

    9. for Driver Side:

      Remove the master switch assembly.

    10. for Front Passenger Side:

      Remove the regulator switch assembly.

    11. Disconnect the connector from the front door window regulator assembly.

  22. REMOVE FRONT DOOR GLASS RUN LH


    1. A0052OL

      Remove the front door glass run.

  23. REMOVE FRONT DOOR BELT MOULDING LH

    Click here

  24. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY LH


    1. A00547NE01
      Text in Illustration
      *1 Temporary Bolt

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.

    2. Remove the 5 bolts.

    3. Remove the front door window regulator assembly.

    4. Remove the temporary bolt from the front door window regulator assembly.

  25. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH


    1. A0052PM

      Remove the screw.

    2. Remove the 3 bolts and frame.

      Note

      Be careful when removing the bolts as the frame may fall and become damaged.

  26. REMOVE FRONT DOOR FIX WINDOW GLASS LH


    1. A0052ZA

      Remove the front door fix window glass and the front door fix window weatherstrip as a unit as shown in the illustration.

  27. REMOVE FRONT DOOR FIX WINDOW WEATHERSTRIP LH


    1. A0053KY

      Remove the front door fix window weatherstrip from the front door fix window glass.

  28. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH


    1. A0056U9

      Remove the bolt and rear lower frame.

  29. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH (for Driver Side)


    1. A0059BA

      Remove the hole plug.

    2. Using a T30 "TORX" wrench, loosen the screw and remove the cover with the door lock key cylinder installed.

    3. A00587K

      Using a screwdriver, disengage the 3 claws and remove the front door outside handle cover from the cylinder.

  30. REMOVE FRONT DOOR OUTSIDE HANDLE COVER RH (for Front Passenger Side)


    1. A0054ND

      Remove the hole plug.

    2. Using a T30 "TORX" wrench, loosen the screw and remove the front door outside handle cover.

  31. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH


    1. w/ Entry and Start System:


      1. A0059L1E10
        Text in Illustration
        *1 Screwdriver
        *2 Connector Cover
        *3 Front Door Outside Handle Assembly
        *4 Front Door Wire LH

        Disconnect the 2 claws of the connector cover as shown in the illustration.

      2. A0053EIE05
        Text in Illustration
        *1 Screwdriver
        *2 Front Door Wire LH

        Push the claw of the connector and disconnect the front door wire as shown in the illustration.

      3. A0057F4E04
        Text in Illustration
        *1 Holder

        Detach the holder as shown in the illustration.

      4. A0057MB

        Remove the handle by sliding and pulling it in the direction indicated by the arrow in the illustration.

    2. w/o Entry and Start System:


      1. A00596RE04
        Text in Illustration
        *1 Holder

        Detach the holder as shown in the illustration.

      2. A00541N

        Remove the handle by sliding and pulling it in the direction indicated by the arrow in the illustration.

  32. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD


    1. A0055Q8

      Detach the 3 claws and remove the pad.

  33. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD


    1. A00584J

      Detach the 2 claws and remove the pad.

  34. REMOVE FRONT DOOR LOCK ASSEMBLY LH

    Click here

  35. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A0058TR

      Remove the front door lock remote control cable assembly.

  36. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A0056X0

      Using a screwdriver, detach the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A005903

      Remove the front door inside locking cable assembly.

  37. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH


    1. w/ Entry and Start System:


      1. A0053TN

        Detach the 2 clamps.

      2. A0052TK

        Using a T30 "TORX" wrench, loosen the screw.

      3. Slide the outside handle frame and door wire to remove it.

        Tech Tips

        Remove the outside handle frame through the service hole.

      4. Pull the front door outside handle frame sub-assembly together with the front door wire away from the vehicle.

      5. A00566U

        Detach the 2 clamps and 2 claws and remove the front door outside handle frame from the front door wire.

    2. w/ Entry and Start System:


      1. A00579P

        Using a T30 "TORX" wrench, loosen the screw.

      2. Slide the outside handle frame to remove it.

        Tech Tips

        Remove the outside handle frame through the service hole.

  38. REMOVE FRONT DOOR LOCK OPEN ROD LH


    1. A00533RE04

      Remove the front door lock open rod as shown in the illustration.

  39. REMOVE FRONT DOOR CHECK ASSEMBLY LH

    A0055BM

    1. Remove the bolt, 2 nuts and door check.

      Tech Tips

      Remove the door check through the service hole.

      Note

      Be careful when removing the bolt and nuts as the door check may fall and become damaged.

  40. REMOVE FRONT DOOR WEATHERSTRIP LH


    1. A0054RAE02

      Using a clip remover, remove the clip labeled A.

    2. Using a clip remover, detach the 16 clips and remove the weatherstrip.

      Tech Tips

      If clips are damaged during removal, replace them.

  41. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH

    Click here

  42. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING LH

    Click here

  43. REMOVE FRONT DOOR FRONT WINDOW FRAME MOULDING LH

    Click here

  44. REMOVE FRONT DOOR NO. 3 WEATHERSTRIP LH


    1. A0058S8

      Remove the 7 clips and weatherstrip from the door.