ROOF HEADLINING(for Sedan) INSTALLATION

PROCEDURE


  1. INSTALL REAR NO. 2 SIDE RAIL SPACER LH

    A0054RK

    1. Attach the 2 claws to install the No. 2 side rail spacer.

  2. INSTALL REAR NO. 2 SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.

  3. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    A0054BF

    1. Attach the 5 claws to install the front shoulder belt anchor plate.

  4. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  5. INSTALL REAR DOOR SCUFF PLATE OUTSIDE LH

    A00548I

    1. Attach the 2 clips to install the rear door scuff plate outside.

  6. INSTALL REAR DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL FRONT DOOR SCUFF PLATE OUTSIDE LH

    A00541D

    1. Attach the 3 clips to install the front door scuff plate outside.

  8. INSTALL FRONT DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  9. INSTALL ROOF HEADLINING ASSEMBLY

    A0053R1E01
    *1 for LHD:
    *2 for RHD:

    1. Place the roof headlining into the vehicle through the passenger door.

      Note

      Be careful not to damage the roof headlining when placing it in the cabin.

    2. Attach the clip to install the roof headlining.

      A00547J

    3. for LHD:


      1. A00530FE03
        *1 for LHD:

        Connect the 2 roof wire connectors.

      2. A00584HE03
        *1 for LHD:

        Connect the 2 clamps.

    4. for RHD:


      1. A00578TE03
        *1 for RHD:

        Connect the roof wire connector.

      2. A0054RFE03
        *1 for RHD:

        Connect the 2 clamps and connector.

    5. A0056MU

      Connect the 4 clamps to the front pillar LH.

    6. A00589A

      w/ Digital Audio Broadcasting Antenna:

      Attach the wire harness clamp and connect the connector to the rear pillar LH.

    7. A00547D

      Install the antenna with the 2 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    8. Connect the clamp to the rear pillar RH.

    9. Connect the 3 connectors.

    10. A0058T6

      Connect the 3 clamps to the front pillar RH.

    11. Connect the connector.

    12. A0055UF

      w/ Rain Sensor:

      Connect the rain sensor connector.

    13. A00534W

      w/ EC Mirror:

      Connect the EC mirror connector.

  10. INSTALL SUNSHADE TRIM HOLDER

    A0054K5E03
    *1 w/o Rear Sunshade:
    *2 Pin
    *3 w/ Rear Sunshade:

    1. Position the pin as shown in the illustration and install the sunshade trim holder.

  11. INSTALL ASSIST GRIP SUB-ASSEMBLY

    A0052MF

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Assemble the assist grip as shown in the illustration.

    2. A0053Y5

      Install the assist grip.

  12. INSTALL REAR ASSIST GRIP ASSEMBLY LH

    A0058ES

    1. Assemble the rear assist grip as shown in the illustration.

    2. A0058NH

      Install the rear assist grip.

  13. INSTALL REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. INSTALL VISOR HOLDER

    A0053WL

    Tech Tips

    Use the same procedure to install the visor holder on the other side.


    1. Attach the 2 claws.

    2. Push in the visor holder as shown in the illustration.

  15. INSTALL VISOR ASSEMBLY LH


    1. A0054JJ

      When clip remains on vehicle:

      Install the clip removed from the vehicle to the visor assembly LH.

    2. A00591B

      Attach the 2 clips to install the visor assembly LH.

    3. A00577D

      Attach the 4 claws to lock the 2 clips with the visor cover.

  16. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  18. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. w/o Rear Monitor:

      Install the inner rear view mirror stay holder cover Click here.

    2. w/ Rear Monitor:

      Install the inner rear view mirror stay holder cover Click here.

  19. INSTALL NO. 1 ROOM LIGHT ASSEMBLY

    A0059B5

    1. Connect the connector.

    2. Attach the 4 claws to install the No. 1 room light.

  20. INSTALL MAP LIGHT ASSEMBLY

    A0053MC

    1. Connect the connector.

    2. Attach the 4 clips to install the map light.

  21. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

    Tech Tips


    • Use the same procedure for RHD and LHD vehicles.

    • The procedure listed below is for LHD vehicles.


    1. Install the lower instrument panel sub-assembly Click here.

  22. INSTALL CONSOLE BOX ASSEMBLY


    1. Install the console box assembly Click here.

  23. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

    Tech Tips


    • Use the same procedure for RHD and LHD vehicles.

    • The procedure listed below the for LHD vehicles.


    1. Install the upper instrument panel sub-assembly Click here.

  24. INSTALL INNER ROOF SIDE GARNISH LH

    A0057YRE01
    Text in Illustration
    *1 Clip A

    1. Install 2 new clips labeled A to the inner roof side garnish.

    2. Attach the 5 clips to install the inner roof side garnish.

  25. INSTALL INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  26. INSTALL CENTER PILLAR GARNISH LH

    A005607

    1. Pass the front seat outer belt floor anchor through the center pillar garnish.

    2. Attach the clip to install the center pillar garnish.

    3. Install the 2 screws.

    4. A0056VK

      Install the front seat outer belt floor anchor with the bolt.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

  27. INSTALL CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  28. INSTALL LAP BELT OUTER ANCHOR COVER

    A0053YN

    Tech Tips

    Use the same procedure for the other lap belt outer anchor cover.


    1. Attach the 3 claws to install the lap belt outer anchor cover.

  29. INSTALL LOWER CENTER PILLAR GARNISH LH

    A0058Y2

    1. Attach the 2 claws and 3 clips to install the lower center pillar garnish.

  30. INSTALL LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  31. INSTALL FRONT PILLAR GARNISH LH


    1. w/ Curtain Shield Airbag:

      Remove the protective cover.

    2. Install a new front pillar garnish clip to the front pillar garnish.

      Tech Tips

      Install the front pillar garnish clip so that it faces as shown in the illustration.

      A00588WE01
      Text in Illustration
      *a CORRECT *b INCORRECT
    3. A0058NK

      Attach the 2 guides.

    4. A0053CDE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Attach the 2 clips to install the front pillar garnish.

  32. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  33. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A0054ZLE02
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Install the rear door opening trim weatherstrip as shown in the illustration.

  34. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  35. INSTALL REAR DOOR SCUFF PLATE LH

    A0053PU

    1. Attach the clip and 6 claws to install the front door scuff plate.

  36. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  37. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    A0052TSE02
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Install the front door opening trim weatherstrip as shown in the illustration.

  38. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  39. INSTALL COWL SIDE TRIM BOARD LH

    A00545O

    1. Attach the clip, claw and guide to install the cowl side trim board.

  40. INSTALL COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  41. INSTALL FRONT DOOR SCUFF PLATE LH

    A0056JY

    1. Attach the 2 clips and 8 claws to install the front door scuff plate.

  42. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  43. INSTALL REAR SIDE SEATBACK ASSEMBLY LH

    Click here

  44. INSTALL REAR SIDE SEATBACK ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  45. INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

    Click here

  46. INSTALL FRONT SEAT ASSEMBLY LH


    1. for Manual Seat:

      Install the front seat assembly Click here.

    2. for Power Seat:

      Install the front seat assembly Click here.

  47. INSTALL FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  48. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.