REAR SEAT OUTER BELT ASSEMBLY(for Wagon) INSTALLATION

CAUTION / NOTICE / HINT

PROCEDURE

1. INSTALL OUTER BELT ANCHOR BRACKET SUB-ASSEMBLY LH

   

   
   

   1. Attach the 2 guides and install the outer belt anchor bracket sub-assembly LH with the 2 bolts.

      Torque:

      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

2. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH

   
   

   1. for LH Side:

      
      
      1. 

         Text in Illustration

         *1	Locking Button

         Connect the pretensioner connector and lock the locking button as shown in the illustration.

         Note

         Securely lock the locking button.

      2. 

         Text in Illustration

         *a	Bolt
         *b	Nut

         Attach the guide and temporarily install the rear seat 3 point type belt assembly LH with the bolt and nut.

      3. Tighten the bolt and nut in the order shown in the illustration.

         Torque:

         for Bolt

         12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }

         for Nut

         42 N*m  { 428 kgf*cm, 31 ft.*lbf }

   2. for RH Side:

      
      
      1. 

         Text in Illustration

         *a	Bolt
         *b	Nut

         Attach the guide (A) and temporarily install the rear seat 3 point type belt assembly RH with the bolt and nut.

      2. Tighten the bolt and nut in the order shown in the illustration.

         Torque:

         for Bolt

         12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }

         for Nut

         42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      3. Attach the wire harness clamp (B).

      4. 

         Text in Illustration

         *1	Locking Button

         Connect the pretensioner connector and lock the locking button as shown in the illustration.

3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

   Click here

4. INSTALL INNER ROOF SIDE GARNISH CAP LH

   Click here

5. INSTALL BACK DOOR WEATHERSTRIP

   Click here

6. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

   Click here

7. INSTALL REAR DOOR SCUFF PLATE LH

   Click here

8. INSTALL REAR FLOOR FINISH PLATE

   Click here

9. INSTALL DECK FLOOR BOX LH

   Click here

10. INSTALL ROPE HOOK ASSEMBLY (w/o Deck Rail)

    Click here

11. INSTALL NO. 6 DECK SIDE TRIM COVER (w/o Deck Rail)

    Click here

12. INSTALL NO. 2 DECK SIDE TRIM COVER (w/o Deck Rail)

    Click here

13. INSTALL FLOOR SIDE RAIL LH (w/ Deck Rail)

    Click here

14. INSTALL REAR DECK FLOOR BOX

    Click here

15. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY

    Click here

16. INSTALL DECK BOARD SUB-ASSEMBLY

    Click here

17. INSTALL DECK BOARD ASSEMBLY

    Click here

18. INSTALL LOWER DECK TRIM SIDE BOARD LH (w/ Partition Board)

    Click here

19. INSTALL ROOM PARTITION NET ASSEMBLY (w/ Partition Net)

    Click here

20. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

    Click here

21. INSTALL REAR SIDE SEATBACK ASSEMBLY LH

    

    
    

    1. Install the claw as shown in the illustration.

    2. Install the side seatback with the bolt.

       Torque:

       7.8 N*m  { 80 kgf*cm, 69 in.*lbf }

    3. 

       Text in Illustration

       *a	Protruding Part

       Install the rear seat 3 point type belt anchor with the bolt.

       Torque:

       42 N*m  { 428 kgf*cm, 31 ft.*lbf }

       Note

       Do not allow the anchor part of the rear seat 3 point type belt to overlap the protruding parts of the floor panel.

    4. Install the seat belt to the belt guide.

    5. Attach the claw to close the cap of the rear seat shoulder belt guide.

    6. Check if the ELR locks.

       Note

       The check should be performed with the outer belt assembly installed.

       
       

       1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

22. INSTALL REAR BENCH TYPE SEAT CUSHION ASSEMBLY

    Click here

23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.