REAR SEAT OUTER BELT ASSEMBLY(for Sedan) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL OUTER BELT ANCHOR BRACKET SUB-ASSEMBLY LH


    1. A0055A0

      Attach the guide and the outer belt anchor bracket sub-assembly LH.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  2. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH


    1. A0053CAE02
      Text in Illustration
      *1 Locking Button

      Connect the pretensioner connector and lock the locking button as shown in the illustration.

      Note

      Securely lock the locking button.

    2. for LH Side:


      1. A005409E01
        Text in Illustration
        *a Bolt
        *b Nut

        Attach the guide (A) and temporarily install the rear seat 3 point type belt assembly LH with the bolt and nut.

      2. Tighten the bolt and nut in the order shown in the illustration.

        Torque:
        for Bolt
        12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
        Torque:
        for Nut
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      3. Attach the wire harness clamp (B).

    3. for RH Side:


      1. A0058J7E01
        Text in Illustration
        *a Bolt
        *b Nut

        Attach the guide and temporarily install the rear seat 3 point type belt assembly LH with the bolt and nut.

      2. Tighten the bolt and nut in the order shown in the illustration.

        Torque:
        for Bolt
        12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
        Torque:
        for Nut
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  3. INSTALL NO. 2 PACKAGE TRAY TRIM PAD

    Tech Tips

    Perform the following procedure if replacing the No. 2 package tray trim pad.


    1. A00586YE06
      Text in Illustration
      *a Mark

      Install a new No. 2 package tray trim pad using double-sided tape.

  4. INSTALL NO. 1 PACKAGE TRAY TRIM PAD

    Tech Tips

    Perform the following procedure if replacing the No. 1 package tray trim pad.


    1. A0054KSE04
      Text in Illustration
      *a Mark

      Install 2 new No. 1 package tray trim pads using double-sided tape as shown in the illustration.

  5. INSTALL NO. 1 ROOM PARTITION BOARD

    A00540R

    1. Attach the 4 clips to install the partition board.

    2. Install the 4 clips.

  6. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

    A005932

    1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

    2. Attach the 5 claws and 2 clips to install the package tray trim panel assembly.

    3. Install the 4 clips.

    4. Connect the connector.

  7. INSTALL REAR SEAT SHOULDER BELT HOLE COVER

    A0054RJ

    1. Attach the 4 claws to install the belt hole cover.

      Tech Tips

      Use the same procedure to install all the belt hole covers.

  8. INSTALL INNER ROOF SIDE GARNISH LH

    Click here

  9. INSTALL INNER ROOF SIDE GARNISH RH

    Click here

  10. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY (for Floor Anchor)

    Click here

  11. INSTALL REAR SIDE SEATBACK ASSEMBLY LH

    Click here

  12. INSTALL REAR SIDE SEATBACK ASSEMBLY RH

    Click here

  13. INSTALL REAR BENCH TYPE SEAT CUSHION ASSEMBLY

    Click here

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.