THEFT DETERRENT SYSTEM Glass Breakage Sensor Circuit

DESCRIPTION

When the glass breakage sensor detects that the back door glass, quarter window glass LH or quarter window glass RH is tapped or broken, the sensor will set off the alarm for 30 seconds.

WIRING DIAGRAM

A0057V3E06
*a Quarter Window Assembly RH
*b Main Body ECU (Instrument Panel Junction Block)
*c Quarter Window Assembly LH
*d Back Door Glass

CAUTION / NOTICE / HINT

Note

As the door control battery is installed between the vehicle battery and main body ECU (instrument panel junction block assembly), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (instrument panel junction block assembly) before performing this troubleshooting procedure Click here.

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (GLASS BREAKAGE SENSOR)


    1. Using the intelligent tester, read the Data List.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Sealed Glas Brak Sen Glass breakage sensor detection / With or Without

      With: Glass breakage sensor operates

      Without: Glass breakage sensor does not operate

      		 -
      OK
      With (glass breakage sensor operates) appears on screen.

    OK

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

    NG

  2. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [INSTRUMENT PANEL JUNCTION BLOCK] - GLASS BREAKAGE SENSOR)

    A0058JXE02

    1. Disconnect the D81 ECU connector.

    2. Disconnect the H23, G45 and M13 sensor connectors.

    3. Disconnect the M7 defogger connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D81-8 (GBS) - H23-2 (SSR+) Always Below 1 Ω
      H23-1 (SSR-) - G45-2 (SSR+)
      G45-1 (SSR-) - M13-2 (SSR+)
      M7-1 - Body ground
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Quarter Window Assembly RH)

      		 *2

      Front view of wire harness connector

      (to Quarter Window Assembly LH)
      *3

      Front view of wire harness connector

      (to Main Body ECU [Instrument Panel Junction Block])

      		 *4

      Front view of wire harness connector

      (to Back Door Glass)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT QUARTER WINDOW ASSEMBLY RH


    1. A0052G7E01
      Text in Illustration
      *1

      Component without harness connected

      (Quarter Window Assembly RH)

      Disconnect the H23 sensor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (SSR-) - 2 (SSR+) Always Below 1 Ω

    NG

    REPLACE QUARTER WINDOW ASSEMBLY RH Click here

    OK

  4. INSPECT QUARTER WINDOW ASSEMBLY LH


    1. A0052G7E01
      Text in Illustration
      *1

      Component without harness connected

      (Quarter Window Assembly LH)

      Disconnect the G45 sensor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (SSR-) - 2 (SSR+) Always Below 1 Ω

    NG

    REPLACE QUARTER WINDOW ASSEMBLY LH Click here

    OK

  5. INSPECT BACK DOOR GLASS


    1. A0057ODE01
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Back Door Glass)

      Disconnect the M13 sensor connector.

    2. Disconnect the M7 defogger connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SSR+) - 1 Always Below 1 Ω

    OK

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

    NG

    REPLACE BACK DOOR GLASS Click here