ENTRY AND START SYSTEM(for Entry Function) CUSTOMIZE PARAMETERS


  1. CUSTOMIZING FUNCTION WITH INTELLIGENT TESTER

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current setting before customizing.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Utility / Customize.

    5. Select the setting by referring to the table below.

      Entry&Start
      Display Default Contents Setting

      Ignition Available Area

      (Entry ignition available area)

      		 ALL Function to choose the available area for the key to start the engine and cancel the steering lock. FRONT/ALL
      Park Wait Time (Waiting time to permit unlocking door after locking) 2.5s Function that sets the waiting time to permit unlocking the door after the door is locked with the entry lock function. 0.5s/1.5s/2.5s/5s
      Trunk Open Mode (Luggage compartment door open mode when vehicle is locked)*1 ON Function to permit opening of the luggage compartment door. ON/OFF
      Back Door Opening Operation (Back door open mode when vehicle is locked)*2 LONG Function to choose the back door open operation mode when the vehicle is locked. LONG/TWICE/OFF

      • *1: for Sedan

      • *2: for Wagon

      Warning
      Display Default Contents Setting
      Key Left in Vehicle Buzzer ON Function that warns the driver when a key is taken out of the vehicle by a passenger. ON/OFF
      Key Low Battery Warning (Warn when key battery becomes weak) ON Function that warns the driver that the key battery power is low. ON/OFF

  2. ENTRY UNLOCK MODE SWITCHING FUNCTION


    1. To use the entry unlock mode switching function, make sure the engine switch is off and simultaneously press and hold the lock switch on the key and another key switch for 5 seconds.


      • When the switches are pressed and held for 5 seconds, the entry door unlock mode changes in the following order: all door unlock mode, driver door unlock mode.

      Note

      After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.


      • All door unlock mode (default):

        When a touch sensor is touched, all doors unlock.

      • Driver door unlock mode:

        When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.

    2. The certification ECU receives this signal from the key and changes the entry and start system to the appropriate entry unlock mode.

    3. The certification ECU sounds the wireless door lock buzzer and combination meter buzzer to inform the user that the mode has been switched.

      Tech Tips

      The function only changes the entry unlock mode of the entry and start system. It does not switch the unlocking of the wireless door lock control.


      • All door unlock mode:

        A0053EUE07

      • Driver door unlock mode:

        A0052MEE07

        Tech Tips

        The above illustrations are for LHD vehicles. For RHD vehicles, the left side and right side are reversed.

  3. KEY CANCEL

    The key cancel operation disables the following functions:


    • Entry Unlock/Lock

    • Key Lock-in Prevention

    • Entry Back Door Open

    • Warning

    • Entry Ignition


    1. The operation procedures are as follows:

      Precondition:

      Engine switch off, driver side door closed and unlocked.


      1. Unlock the driver side door once with the unlock switch of the key.

      2. Open the driver door within 5 seconds.

      3. Unlock the driver side door twice with the unlock switch of the key within 5 seconds.

      4. Perform close → open twice for the driver door within 30 seconds.

        (Driver door: Open condition → Close → Open → Close → Open)

      5. Unlock the driver side door twice with the unlock switch of the key within 5 seconds.

      6. Perform close → open once for the driver door within 30 seconds.

        (Driver door: Open condition → Close → Open)

      7. Close the driver door within 5 seconds.

        When key cancel is activated, the wireless door lock buzzer sounds twice.

        To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.