LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2325

DTC Code DTC Name
B2325 LIN Communication Bus Malfunction

DESCRIPTION

The main body ECU (instrument panel junction block assembly) intermittently monitors the LIN communication bus between the components related to the door, double lock door control relay*2 and sliding roof drive gear*1. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors, double lock door control relay*2 and sliding roof drive gear*1 is detected consecutively 3 times.

*1: w/ Roof Sunshade System

*2: w/ Double Locking System

DTC Code DTC Detection Condition Trouble Area
B2325 The main body ECU (instrument panel junction block assembly) detects a malfunction in the LIN communication bus between components related to the doors, double lock door control relay*2 and sliding roof drive gear*1 consecutively 3 times.

  • Master switch

  • Front door window regulator LH

  • Front door window regulator RH

  • Rear door window regulator LH (w/ Rear Door Power Window)

  • Rear door window regulator RH (w/ Rear Door Power Window)

  • Sliding roof drive gear (w/ Roof Sunshade System)

  • Double lock door control relay (w/ Double Locking System)

  • Main body ECU (instrument panel junction block assembly)

  • Harness or connector

*1: w/ Roof Sunshade System

*2: w/ Double Locking System

WIRING DIAGRAM

A0055A5E05

CAUTION / NOTICE / HINT

Note

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

Tech Tips

When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform troubleshooting for the LIN communication stop DTC. Then perform troubleshooting for DTC B2325.

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT

  2. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    USE SIMULATION METHOD TO CHECK Click here

    A

  3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MASTER SWITCH)


    1. A00561JE02
      Text in Illustration
      *1 for LHD
      *2 for RHD
      *3

      Front view of wire harness connector

      (to Main Body ECU)
      *4

      Front view of wire harness connector

      (to Master Switch)

      Disconnect the D79 ECU connector.

    2. Disconnect the E14*1 or E8*2 switch connector.

      *1: for LHD

      *2: for RHD

    3. Measure the resistance and voltage according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D79-23 (LIN2) - E14-17 (LIN1)*1 or E8-17 (LIN1)*2 Always Below 1 Ω
      D79-23 (LIN2) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CLEAR DTC


    1. Reconnect the D79 ECU connector.

    2. Disconnect the E14*1 or E8*2 switch connector.

      *1: for LHD

      *2: for RHD

    3. Clear the DTCs Click here.


    NEXT

  5. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    A

  6. CLEAR DTC

    *1: for LHD

    *2: for RHD


    1. Reconnect the E14*1 or E8*2 switch connector.

    2. Disconnect the E15*1 or E20*2 regulator connector.

    3. Clear the DTCs Click here.


    NEXT

  7. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE FRONT DOOR WINDOW REGULATOR LH Click here

    A

  8. CLEAR DTC


    1. Reconnect the E15*1 or E20*2 regulator connector.

      *1: for LHD

      *2: for RHD

    2. Disconnect the E6 regulator connector.

    3. Clear the DTCs Click here.


    NEXT

  9. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output (w/ Rear Door Power Window) A
      DTC B2325 is output (w/o Rear Door Power Window, w/ Double Locking System) B
      DTC B2325 is output (w/o Rear Door Power Window, w/o Double Locking System, w/ Roof Sunshade System) C
      DTC B2325 is output (w/o Rear Door Power Window, w/o Double Locking System, w/o Roof Sunshade System) D
      DTC B2325 is not output E

    B

    CLEAR DTC Click here

    C

    CLEAR DTC Click here

    D

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

    E

    REPLACE FRONT DOOR WINDOW REGULATOR RH Click here

    A

  10. CLEAR DTC


    1. Reconnect the E6 regulator connector.

    2. Disconnect the F4 regulator connector.

    3. Clear the DTCs Click here.


    NEXT

  11. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE REAR DOOR WINDOW REGULATOR LH Click here

    A

  12. CLEAR DTC


    1. Reconnect the F4 regulator connector.

    2. Disconnect the F9 regulator connector.

    3. Clear the DTCs Click here.


    NEXT

  13. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output (w/ Double Locking System) A
      DTC B2325 is output (w/o Double Locking System, w/ Roof Sunshade System) B
      DTC B2325 is output (w/o Double Locking System, w/o Roof Sunshade System) C
      DTC B2325 is not output D

    B

    CLEAR DTC Click here

    C

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

    D

    REPLACE REAR DOOR WINDOW REGULATOR RH Click here

    A

  14. CLEAR DTC


    1. Reconnect the F9 regulator connector.

    2. Disconnect the D107 relay connector.

    3. Clear the DTCs Click here.


    NEXT

  15. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output (w/ Roof Sunshade System) A
      DTC B2325 is output (w/o Roof Sunshade System) B
      DTC B2325 is not output C

    A

    CLEAR DTC Click here

    B

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

    C

    REPLACE DOUBLE LOCK DOOR CONTROL RELAY Click here

  16. CLEAR DTC


    1. w/ Double Locking System:

      Reconnect the D107 relay connector.

    2. w/o Double Locking System:

      Reconnect the F9 regulator connector.

    3. Disconnect the K9 drive gear connector.

    4. Clear the DTCs Click here.


    NEXT

  17. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    A

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

    B

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY Click here

  18. CLEAR DTC


    1. Reconnect the E6 regulator connector.

    2. Disconnect the D107 relay connector.

    3. Clear the DTCs Click here.


    NEXT

  19. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output (w/ Roof Sunshade System) A
      DTC B2325 is output (w/o Roof Sunshade System) B
      DTC B2325 is not output C

    A

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    B

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

    C

    REPLACE DOUBLE LOCK DOOR CONTROL RELAY Click here

  20. CLEAR DTC


    1. w/ Double Locking System:

      Reconnect the D107 relay connector.

    2. w/o Double Locking System:

      Reconnect the E6 regulator connector.

    3. Disconnect the K9 ECU connector.

    4. Clear the DTCs Click here.


    NEXT

  21. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    A

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

    B

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY Click here