ELECTRIC PARKING BRAKE SYSTEM, Diagnostic DTC:C1203/73

DTC Code DTC Name
C1203/73 Vehicle Information Mismatch

DESCRIPTION

The circuit is used to send electric parking brake system information from the electric parking brake ECU to the ECM, and engine control information from the ECM to the electric parking brake ECU.

DTC Code DTC Detection Condition Trouble Area
C1203/73

One of the following conditions is met:


  • The stored variant coding parameters are not valid for this software version.

  • The data provided by CAN concerning variant coding parameters are not defined in ROM.

  • The data provided by CAN concerning variant coding parameters are different from non-volatile memory.

  • ECM

  • Main body ECU (Instrument panel junction block assembly)

  • Electric parking brake ECU (Parking brake with bracket actuator assembly)

CAUTION / NOTICE / HINT

Note


  • Before performing work, turn the ignition switch off and wait approximately 20 seconds to make sure that the parking brake cannot operate.

  • When replacing the parking brake with bracket actuator assembly, perform zero point calibration Click here.

  • As the door control battery is installed between the vehicle battery and main body ECU (instrument panel junction block assembly), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (instrument panel junction block assembly) before performing this troubleshooting procedure.*

    *: w/ Rear Pretensioner

PROCEDURE


  1. CHECK ENGINE TYPE


    1. Check the engine type.

      Result
      Result Proceed to
      1ZR-FAE A
      2ZR-FAE B
      3ZR-FAE C
      3ZR-FE D

    B

    CHECK PART NUMBER (ECM) Click here

    C

    CHECK PART NUMBER (ECM) Click here

    D

    CHECK PART NUMBER (ECM) Click here

    A

  2. CHECK PART NUMBER (ECM)


    1. Check that the part number of the installed ECM is correct.

      Result
      Result Proceed to
      ECM has the incorrect part number. A
      ECM has the correct part number. B

    A

    REPLACE ECM Click here

    B

    READ VALUE USING INTELLIGENT TESTER (HANDLE POSITION VARIANT) Click here

  3. CHECK PART NUMBER (ECM)


    1. Check that the part number of the installed ECM is correct.

      Result
      Result Proceed to
      ECM has the incorrect part number. A
      ECM has the correct part number. B

    A

    REPLACE ECM Click here

    B

    READ VALUE USING INTELLIGENT TESTER (HANDLE POSITION VARIANT) Click here

  4. CHECK PART NUMBER (ECM)


    1. Check that the part number of the installed ECM is correct.

      Result
      Result Proceed to
      ECM has the incorrect part number. A
      ECM has the correct part number. B

    A

    REPLACE ECM Click here

    B

    READ VALUE USING INTELLIGENT TESTER (HANDLE POSITION VARIANT) Click here

  5. CHECK PART NUMBER (ECM)


    1. Check that the part number of the installed ECM is correct.

      Result
      Result Proceed to
      ECM has the incorrect part number. A
      ECM has the correct part number. B

    A

    REPLACE ECM Click here

    B

  6. READ VALUE USING INTELLIGENT TESTER (HANDLE POSITION VARIANT)


    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Select the Data List mode on the intelligent tester Click here.

      Electric Parking Brake
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Handle Position Variant

      Steering wheel location variant/

      No code, LHD or RHD

      		 - -

    4. Check if the steering wheel location displayed in the Data List matches the steering wheel location of the vehicle.

      OK
      The steering wheel location displayed in the Data List matches the steering wheel location of the vehicle.

    NG

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

    OK

  7. RECONFIRM DTC


    1. Clear the DTCs Click here.

    2. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC is output. A
      DTC is not output. B

    A

    REPLACE PARKING BRAKE WITH BRACKET ACTUATOR ASSEMBLY Click here

    B

    USE SIMULATION METHOD TO CHECK Click here