REAR LOWER ARM INSTALLATION

PROCEDURE


  1. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

    A0055FT

    1. Temporarily install the rear No. 2 suspension arm to the suspension member with the bolt and nut.

  2. INSTALL REAR UPPER COIL SPRING INSULATOR LH

    Click here

  3. INSTALL REAR LOWER COIL SPRING INSULATOR LH

  4. INSTALL REAR COIL SPRING LH

    Click here

  5. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY LH

    A00568X

    1. Temporarily install the rear shock absorber to the rear No. 2 suspension arm with the bolt and nut.

  6. INSTALL REAR STABILIZER LINK ASSEMBLY LH

    Click here

  7. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (for LED Headlight)

    Click here

  8. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    1. for Turnbuckle Type:


      1. A0056Q7

        Temporarily install the rear No. 1 suspension arm to the rear axle carrier with a new nut.

      2. A0054MD

        Temporarily install the rear No. 1 suspension arm to the suspension member with the bolt and nut.

    2. for Cam Type:


      1. A0052CC

        Temporarily install the rear No. 1 suspension arm to the rear axle carrier with a new nut.

      2. A005820

        Using the rear suspension toe adjust cam sub-assembly, No. 2 camber adjust cam and nut, temporarily install the rear No. 1 suspension arm assembly to the rear suspension member sub-assembly.

        Note


        • Insert the rear suspension toe adjust cam sub-assembly from the rear of the vehicle.

        • Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.

  9. STABILIZE SUSPENSION

    Click here

  10. TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

    A0059E4

    1. Tighten the 2 bolts and 2 nuts of the rear No. 2 suspension arm assembly.

      Torque:
      90 N*m  { 918 kgf*cm, 66 ft.*lbf }

      Note

      Since a stopper nut is used, tighten the bolt.

  11. TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH

    A00559Z

    1. Tighten the bolt of the rear shock absorber.

      Torque:
      90 N*m  { 918 kgf*cm, 66 ft.*lbf }

      Note

      Since a stopper nut is used, tighten the bolt.

  12. TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    1. for Turnbuckle Type:


      1. A0056Q7

        Tighten the nut of the rear No. 1 suspension arm.

        Torque:
        100 N*m  { 1020 kgf*cm, 74 ft.*lbf }
      2. A0054MD

        Tighten the bolt and nut of the rear No. 1 suspension arm.

        Torque:
        90 N*m  { 918 kgf*cm, 66 ft.*lbf }

        Note

        Since a stopper nut is used, tighten the bolt.

    2. for Cam Type:


      1. A0052CC

        Tighten the nut of the rear No. 1 suspension arm.

        Torque:
        100 N*m  { 1020 kgf*cm, 74 ft.*lbf }
      2. A0053EJE02
        Text in Illustration
        *a Matchmarks

        Align the matchmarks on the No. 2 camber adjust cam, rear suspension toe adjust cam sub-assembly and rear suspension member sub-assembly.

      3. Fully tighten the nut to install the rear No. 1 suspension arm assembly.

        Torque:
        100 N*m  { 1020 kgf*cm, 74 ft.*lbf }

        Note

        Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.

  13. INSTALL REAR SUSPENSION ARM COVER LH

    A005772

    1. Install the cover with the 2 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  14. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  16. INSPECT AND ADJUST REAR WHEEL ALIGNMENT


    1. Inspect and adjust the rear wheel alignment Click here.

  17. ADJUST HEADLIGHT ASSEMBLY


    1. for Halogen Headlight:

      Adjust the headlight assembly Click here.

    2. for HID Headlight:

      Adjust the headlight assembly Click here.