TRANSMISSION CONTROL CABLE INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET


    1. Install the No. 1 transmission control cable bracket to the continuously variable transaxle assembly with the 2 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    2. Attach the clamp.

  2. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

    Note

    Before installing the transmission control cable assembly, check that the park/neutral position switch and shift lever are in neutral.


    1. A0057JC

      Put the transmission control cable into the cabin and connect the transmission control cable with the 2 nuts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    2. A0053WN

      Connect the transmission control cable support with the bolt.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    3. A0054OJ

      Connect the transmission control cable to the bracket with a new clip.

    4. Connect the transmission control cable to the control shaft lever with the nut.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    5. Turn the nut of the transmission control cable 180° counterclockwise. While holding the nut in place, push in the stopper until the stopper clicks twice.

      A0056XJE03
      Text in Illustration
      *1 Stopper *2 Nut
      A0054CA Turn in this Direction A0056SR Push in this Direction

    6. Install the outer part of the transmission control cable to the shift lever assembly. Check that the spring is positioned at "A" and push in the stopper.

      A0053NRE03
      Text in Illustration
      *1 Stopper *2 Nut
      *3 Shift Lever Assembly *4 Spring
      A0054CA Install in this Direction - -

      Tech Tips

      If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.

    7. A0058LJE03
      Text in Illustration
      *1 Transmission Control Cable Lock Piece
      *a Side View
      *b Bottom View
      A0054CA Push in this Direction

      Push the 2 claws together at the top of the transmission control cable lock piece. While holding the 2 claws together, push the 2 lugs on the bottom of the lock piece toward each other and upward to pull out the lock piece.

    8. A0055MCE01
      Text in Illustration
      *1 Transmission Control Cable Lock Piece

      Connect the end of the cable to the shift lever assembly.

      Note


      • Make sure that the transmission control cable lock piece is pulled up.

      • Push on the end of the cable all the way to the base of the pin.

    9. A0058KKE03
      Text in Illustration
      *1 Transmission Control Cable Lock Piece
      *2 Adjuster Case
      A0054CA Push in this Direction

      Push the transmission control cable lock piece into the adjuster case.

      Note

      Securely push in the transmission control cable lock piece until it locks.

  3. INSTALL FRONT FLOOR NO. 1 HEAT INSULATOR

    A0053XU

    1. Install the front floor No. 1 heat insulator with the 5 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  4. INSTALL FRONT EXHAUST PIPE ASSEMBLY

    Click here

  5. CONNECT HEATED OXYGEN SENSOR CONNECTOR

  6. INSTALL NO. 2 ENGINE UNDER COVER

    Click here

  7. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  8. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


    1. Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.

  9. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

    Click here

  10. INSTALL NO. 2 CYLINDER HEAD COVER

    Click here

  11. INSPECT SHIFT LEVER POSITION

    Click here

  12. ADJUST SHIFT LEVER POSITION

    Click here

  13. INSTALL CONSOLE BOX ASSEMBLY

    Click here