FRONT DRIVE SHAFT ASSEMBLY(for 1ZR-FAE, 2ZR-FAE) REASSEMBLY

PROCEDURE


  1. INSTALL FRONT DRIVE SHAFT DUST COVER LH


    1. A0057CHE01

      Using SST and a press, press on a new drive shaft dust cover.

      SST
      09527-10011

      Note


      • The dust cover should be installed completely.

      • Be careful not to damage the dust cover.

  2. INSTALL FRONT DRIVE SHAFT DUST COVER RH

    Tech Tips

    Use the same procedures described for the LH side.

  3. INSTALL FRONT AXLE OUTBOARD JOINT BOOT LH

    A00574BE23
    Text in Illustration
    *a Protective Tape

    Tech Tips

    Before installing the boot, wrap the spline of the drive shaft with protective tape to prevent the boot from being damaged.


    1. Hold the front drive shaft in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    2. Install new parts to the outboard joint shaft in the following order.


      1. No. 2 axle outboard joint boot clamp

      2. Outboard joint boot

      3. Outboard joint boot clamp

    3. Pack the outboard joint shaft and boot with grease from the boot kit.

      Standard grease capacity
      120 to 130 g (4.24 to 4.58oz.)

  4. INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP LH


    1. Hold the front drive shaft in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    2. Secure the No. 2 axle outboard joint boot clamp to the boot.

    3. A0058D9E01
      Text in Illustration
      *a Turn
      *b Hold

      Place SST onto the No. 2 axle outboard joint boot clamp.

      SST
      09521-24010

    4. Tighten SST so that the No. 2 axle outboard joint boot clamp is pinched.

      Note

      Do not overtighten SST.

    5. A0056CVE05

      Using SST, adjust the clearance of the clamp.

      SST
      09240-00020
      Standard clearance
      0.5 to 1.5 mm (0.0197 to 0.0591 in.)

      If the measured value exceeds the specified value, retighten the clamp.

  5. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH


    1. Hold the front drive shaft in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    2. Secure the outboard joint boot clamp to the boot.

    3. A00590DE01
      Text in Illustration
      *a Turn
      *b Hold

      Place SST onto the outboard joint boot clamp.

      SST
      09521-24010

    4. Tighten SST so that the outboard joint boot clamp is pinched.

      Note

      Do not overtighten SST.

    5. A0059LTE04

      Using SST, adjust the clearance of the clamp.

      SST
      09240-00020
      Standard clearance
      0.5 to 1.5 mm (0.0197 to 0.0591 in.)

      If the measured value exceeds the specified value, retighten the clamp.

  6. INSTALL FRONT DRIVE SHAFT DAMPER LH


    1. Install the drive shaft damper to the drive shaft.

      Note

      Make sure that the damper is on the shaft groove.

    2. A00591AE02

      Adjust the position of the damper so that the dimension is as described below.

      Standard dimension (A)
      161 to 165 mm (6.34 to 6.50 in.)

  7. INSTALL FRONT DRIVE SHAFT DAMPER CLAMP LH


    1. Hold the front drive shaft in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    2. Install a new drive shaft damper clamp to the damper.

      Note

      Be sure to install the clamp on the inboard joint side in the correct position.

    3. A00541JE01
      Text in Illustration
      *a Turn
      *b Hold

      Place SST onto the damper clamp.

      SST
      09521-24010

    4. Tighten SST so that the damper clamp is pinched.

      Note

      Do not overtighten SST.

    5. A0056NIE01

      Using SST, adjust the clearance of the damper clamp.

      SST
      09240-00020
      Standard clearance
      0.5 to 1.5 mm (0.0197 to 0.0591 in.)

      If the measured value exceeds the specified value, retighten the clamp.

  8. INSTALL FRONT DRIVE SHAFT DAMPER RH


    1. Install the drive shaft damper to the drive shaft.

    2. A0057A5E04

      Adjust the position of the damper so that the dimension is as described below.

      Standard dimension (B)
      442 to 446 mm (17.4 to 17.6 in.)

  9. INSTALL DRIVE SHAFT DAMPER SETTING CLAMP


    1. Hold the front drive shaft in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    2. Install a new drive shaft damper clamp to the damper.

      Note

      Be sure to install the clamp on the inboard joint side in the correct position.

    3. A00541JE01
      Text in Illustration
      *a Turn
      *b Hold

      Place SST onto the damper clamp.

      SST
      09521-24010

    4. Tighten SST so that the damper clamp is pinched.

      Note

      Do not overtighten SST.

    5. A0056NIE01

      Using SST, adjust the clearance of the damper clamp.

      SST
      09240-00020
      Standard clearance
      0.5 to 1.5 mm (0.0197 to 0.0591 in.)

      If the measured value exceeds the specified value, retighten the clamp.

  10. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY LH


    1. Wrap the spline of the outboard joint shaft with protective tape to prevent the boot from being damaged.

    2. Install new parts to the outboard joint shaft in the following order.


      1. Inboard joint boot clamp

      2. Inboard joint boot

      3. No. 2 axle inboard joint boot clamp

    3. Remove the protective tape.

    4. A0058UIE10

      Place the beveled side of the tripod axial spline toward the outboard joint.

    5. Align the matchmarks placed before removal.

      Text in Illustration
      *a Matchmark

    6. Using a brass bar and hammer, tap the tripod onto the drive shaft.

      Note


      • Do not tap the rollers.

      • Be sure to install the tripod in the correct direction.

    7. Pack the inboard joint shaft and boot with grease from the boot kit.

      Standard grease capacity
      155 to 171 g (5.47 to 6.03 oz.)
    8. A00583G

      Using a snap ring expander, install a new shaft snap ring.

    9. A0053V8E16
      Text in Illustration
      *a Matchmark

      Align the matchmarks and install the inboard joint to the outboard joint shaft.

  11. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  12. INSTALL FRONT AXLE INBOARD JOINT BOOT


    1. Install the inboard joint boot to the inboard joint.

    2. A0052IGE22

      Check that the 2 boots are not stretched or contracted when the drive shaft is at the standard length.

      Dimension (A)
      for LH Side for RH Side
      603.28 mm (23.8 in.) 886.28 mm (34.9 in.)

  13. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP LH


    1. Hold the front drive shaft in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    2. Secure the inboard joint boot clamp to the boot.

    3. A0053X2E02
      Text in Illustration
      *a Turn
      *b Hold

      Place SST onto the inboard joint boot clamp.

      SST
      09521-24010

    4. Tighten SST so that the clamp is pinched.

      Note

      Do not overtighten SST.

    5. A0059LTE02

      Using SST, adjust the clearance of the clamp.

      SST
      09240-00020
      Standard clearance
      0.5 to 1.5 mm (0.0197 to 0.0591 in.)

      If the measured value exceeds the specified value, retighten the clamp.

  14. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedures described for the LH side.

  15. INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP LH


    1. A005535

      Using needle-nose pliers, install the axle inboard joint boot clamp as shown in the illustration.

      Note

      Be careful not to damage the boot.

  16. INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedures described for the LH side.

  17. INSPECT DRIVE SHAFT

    Click here