FRONT POWER SEAT MOTOR ASSEMBLY(for Rear Lifter) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL POWER SEAT MOTOR ASSEMBLY (for Rear Lifter)


    1. Install a nose piece to an air riveter or hand riveter. Then insert the mandrel part of a new φ4 mm rivet into the nose piece.

    2. B0040LZE01
      Text in Illustration
      *1 Air Riveter

      Using the air riveter or hand riveter, install the power seat motor assembly with a new rivet.

      Tech Tips

      If the rivet cannot be cut, pull it once and cut it.

      Note


      • B0040FUE65
        *1 INCORRECT
        *2 Riveter
        *3 Mandrel
        *4 CORRECT

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      • B0040KJE43
        *1 Riveter
        *2 INCORRECT
        *3 CORRECT

        Confirm that the rivet is seated properly against the motor.

      • Do not tilt the riveter when installing the rivet to the power seat motor assembly.

      • Do not leave any space between the rivet head and power seat motor assembly.

      • B0040LLE39
        *1 Riveter
        *2 INCORRECT
        *3 CORRECT

        Do not leave any space between the power seat motor assembly and front seat adjuster. Firmly hold together the 2 items while installing the rivet.

    3. B0040K5E01
      Text in Illustration
      *1 Air Riveter

      Using the air riveter or hand riveter, install 2 new rivets.

      Tech Tips

      If the rivet cannot be cut, pull it once and cut it.

      Note


      • B0040FUE65
        *1 INCORRECT
        *2 Riveter
        *3 Mandrel
        *4 CORRECT

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      • B0040KJE43
        *1 Riveter
        *2 INCORRECT
        *3 CORRECT

        Confirm that the rivets are seated properly against the front seat adjuster.

      • Do not tilt the riveter when installing the rivet to the front seat adjuster.

      • Do not leave any space between the rivet head and front seat adjuster.

      • B0040LLE39
        *1 Riveter
        *2 INCORRECT
        *3 CORRECT

        Do not leave any space between the front seat adjuster and power seat motor assembly. Firmly hold together the 2 items while installing the rivet.

  2. INSTALL SEAT CUSHION COVER WITH PAD

    Click here

  3. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    Click here

  4. INSTALL FRONT SEAT INNER CUSHION SHIELD LH

    Click here

  5. INSTALL FRONT POWER SEAT SWITCH

    Click here

  6. INSTALL FRONT SEAT CUSHION SHIELD LH WITH FRONT SEAT INNER NO. 1 CUSHION SHIELD

    Click here

  7. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

    Click here

  8. INSTALL RECLINING POWER SEAT SWITCH KNOB

    Click here

  9. INSTALL FRONT SEAT ASSEMBLY

    Click here

  10. CHECK SRS WARNING LIGHT

    Click here

  11. INSPECT FRONT SEAT ASSEMBLY


    1. Check the power seat operation Click here.

    2. Check the seat heater operation.


      1. Turn the ignition switch to ON.

      2. Operate the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.