FRONT SEAT ASSEMBLY(for Power Seat) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL SEAT POSITION AIRBAG SENSOR

    Click here

  2. INSTALL REAR UPPER NO. 2 SEAT TRACK COVER


    1. B0040K7

      Attach the 3 claws to install the rear upper No. 2 seat track cover.

  3. INSTALL REAR UPPER SEAT TRACK COVER


    1. B0040KR

      Attach the 3 claws to install the rear upper seat track cover.

  4. INSTALL POWER SEAT MOTOR ASSEMBLY (for Rear Lifter)

    Click here

  5. INSTALL POWER SEAT MOTOR ASSEMBLY (for Front Vertical)

    Click here

  6. INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY


    1. B0040FL

      Attach the 8 hooks to install the separate type front seat cushion spring assembly to the front seat adjuster assembly LH.

    2. B0040I9

      for Front Passenger Side:

      Attach the 2 clamps to install the connector holder.

  7. INSTALL FRONT SEAT ADJUSTER ASSEMBLY LH


    1. B0040LJ

      Using a T50 "TORX" socket wrench, install the front seat adjuster assembly LH with the 4 "TORX" bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

  8. INSTALL FRONT SEAT BELT INNER ANCHOR BRACKET COVER LH (for Front Passenger Side)


    1. B0040QN

      Attach the guide to install the front seat belt inner anchor bracket cover LH with the screw.

  9. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)


    1. B0040P6

      Attach the guide to install the front seat lower cushion shield LH with the screw.

  10. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Front Passenger Side)

    Tech Tips

    Use the same procedure described for the front seat lower cushion shield LH.

  11. INSTALL FRONT SEAT WIRE LH


    1. Attach the claw.

      B0040JS

    2. Attach the 3 wire harness clamps.

    3. Connect the 3 connectors.

    4. B0040KT

      Attach the 2 wire harness clamps and connect the connector to install the front seat wire LH.

  12. INSTALL POSITION CONTROL ECU ASSEMBLY (for Driver Side)


    1. B0040PX

      Install the position control ECU assembly with the 2 bolts.

    2. Connect the 2 connectors.

  13. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH


    1. B0040KD

      Attach the claw to install the seat climate control controller LH.

  14. INSTALL POWER SEAT MOTOR ASSEMBLY (for Reclining)

    Click here

  15. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH

    Click here

  16. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH

    Click here

  17. INSTALL SEPARATE TYPE FRONT SEATBACK PAD


    1. B0040ID

      Install the separate type front seatback pad.

  18. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH

    Click here

  19. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. Temporarily install the separate type front seatback cover.

    2. B0040KZE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 3 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    3. B0040ORE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 3 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    4. B0040LGE02
      Text in Illustration
      *1 Hog Ring Pliers
      *2 Hog Ring
      *3 Hook

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    5. Attach the 2 hooks.

    6. B0040MLE02
      Text in Illustration
      *1 Hog Ring Pliers
      *2 Strap

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 5 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

      • When installing the separate type front seatback cover, make sure to pass the straps of the separate type front seatback cover through the hog rings.

    7. B0040NL

      Attach the 2 claws to install the 2 front seat headrest supports.

    8. B0040P5

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

    9. B0040PF

      Attach the 2 hooks.

    10. B0040LH

      Attach the 2 hooks to connect the 2 straps.

    11. B0040FP

      Attach the 2 hooks at the bottom of the separate type front seatback cover.

    12. B0040N5

      Attach the 2 hooks.

  20. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY LH

    Tech Tips

    Perform this procedure when it is necessary to remove and reinstall or replace the separate type front seatback assembly LH.


    1. B0040PE

      Using a T50 "TORX" socket wrench, install the separate type front seatback assembly to the front seat adjuster assembly LH with the 4 "TORX" bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }
    2. B0040M4

      Connect the connector and attach the 2 wire harness clamps.

    3. B0040Q9

      for Driver side:

      Connect the connector.

    4. B0040P5

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

    5. B0040PF

      Attach the 2 hooks.

    6. B0040LH

      Attach the 2 hooks to connect the 2 straps.

    7. B0040FP

      Attach the 2 hooks at the bottom of the separate type front seatback cover.

    8. B0040N5

      Attach the 2 hooks.

    9. B0040JE

      Attach the claw and connect the connector.

    10. Attach the 2 wire harness clamps.

  21. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH

    Click here

  22. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. B0040M1

      Attach the 13 hooks to install the separate type front seat cushion cover to the separate type front seat cushion pad.

      Note


      • Be careful not to damage the separate type front seat cushion cover.

      • When attaching the hooks, avoid wrinkling the separate type front seat cushion cover.

  23. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


    1. Attach the 6 hooks to install the seat cushion cover with pad.

      B0040FZ

    2. Connect the connector.

    3. B0040NF

      Attach the wire harness clamp.

    4. B0040KO

      for Front Passenger Side:

      Attach the claw to connect the connector.

    5. B0040IO

      Connect the connector.

    6. B0040O8

      Attach the claw to connect the connector.

    7. Attach the wire harness clamp.

    8. for Type A:

      Connect the 2 connectors.

    9. B0040FV

      for Type B:

      Connect the connector.

    10. B0040HE

      Attach the 2 hooks.

  24. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. B0040QQ

      Attach the hook to install the front seat inner cushion shield LH with the screw.

  25. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

    Click here

  26. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)

    Click here

  27. INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR (for Driver Side)


    1. B0040PB

      Attach the 2 clamps and connect the wire harness.

    2. B0040K4

      Attach the 2 claws and 2 guides to install the seat slide position sensor protector with the screw.

  28. INSTALL FRONT POWER SEAT SWITCH LH

    Click here

  29. INSTALL LUMBAR FRONT POWER SEAT SWITCH (for Driver Side)

    Click here

  30. INSTALL FRONT SEAT NO. 1 INNER CUSHION SHIELD LH


    1. B0040IR

      Attach the 2 claws to install the front seat No. 1 inner cushion shield LH to the front seat cushion shield LH.

  31. INSTALL FRONT SEAT CUSHION SHIELD LH WITH FRONT SEAT NO. 1 INNER CUSHION SHIELD LH


    1. B0040MJ

      for Driver Side:

      Connect the connector.

    2. B0040L8

      Attach the hook to install the front seat cushion shield LH with front seat inner No. 1 cushion shield LH.

    3. Install the 2 screws.

    4. B0040KK

      Attach the 2 claws and install the 2 screws.

    5. B0040Q0

      Attach the 2 rubber bands.

  32. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. B0040IN

      Attach the 4 claws to install the slide and vertical power seat switch knob.

  33. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. B0040OH

      Attach the 2 claws to install the reclining power seat switch knob.