FRONT SEAT ASSEMBLY(for Power Seat) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL NO. 2 REAR UPPER SEAT TRACK COVER


    1. B0040K7

      Attach the 3 claws to install the No. 2 rear upper seat track cover.

  2. INSTALL REAR UPPER SEAT TRACK COVER


    1. B0040KR

      Attach the 3 claws to install the rear upper seat track cover.

  3. INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY


    1. B0040FL

      Attach the 8 hooks to install the separate type front seat cushion spring assembly to the front seat adjuster assembly LH.

  4. INSTALL FRONT SEAT ADJUSTER ASSEMBLY LH


    1. A0058V9

      Using a T50 "TORX" socket wrench, install the front seat adjuster assembly LH with the 4 "TORX" bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

  5. INSTALL FRONT SEAT INNER BELT ANCHOR BRACKET COVER LH


    1. A0057JP

      Install the front seat inner belt anchor bracket cover LH with the screw.

  6. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH


    1. A0058YC

      Install the front seat lower cushion shield LH with the screw.

  7. INSTALL FRONT SEAT WIRE LH


    1. A0056AS

      Attach the 3 claws to install the front seat wire LH.

    2. Attach the 3 wire harness clamps and connect the connector.

    3. A0053L0

      Attach the wire harness clamp.

    4. A0056H9

      Attach the wire harness clamp.

  8. INSTALL POSITION CONTROL ECU ASSEMBLY (for Driver Side)


    1. B0040PX

      Install the position control ECU assembly with the 2 bolts.

    2. Connect the 2 connectors.

  9. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH


    1. A00555T

      Attach the claw to install the seat climate control controller LH.

    2. Connect the connector.

  10. INSTALL POWER SEAT MOTOR ASSEMBLY (for Reclining)

    Click here

  11. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH

    Click here

  12. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH

    Click here

  13. INSTALL FRONT SEATBACK HEATER ASSEMBLY

    Click here

  14. INSTALL SEPARATE TYPE FRONT SEATBACK PAD

    A00578Q

    1. Install the separate type front seatback pad.

  15. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. A0052NQ

      Attach the 2 hooks.

    2. A0053VY

      Attach the 2 claws to install the 2 front seat headrest supports.

    3. A00539Y

      Install the front seat headrest assembly.

      Note

      Push in the front seat headrest assembly until the headrest lock engages.

    4. A0055M9

      Pass the cable through the hole of the seatback frame.

    5. A0057YK

      Attach the 2 claws to install the clip.

    6. B0040NTE02
      Text in Illustration
      *1 Cable End

      Pull the cable through the clip until the cable end reaches the clip.

    7. A0058RD

      Install a new cable tie.

    8. B0040JKE02
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 2 hooks and close the seatback mat.

    9. Using hog ring pliers, install a new hog ring.

    10. A0058D2

      Attach the 2 claws to connect the cable to the active headrest lower unit.

    11. A00556Q

      Attach the 2 claws to install the active headrest lower unit.

    12. B0040PLE02
      Text in Illustration
      *1 Cable End
      A0054DN Pull

      Pull the cable and connect the cable end to the active headrest lower unit.

    13. A0056MF

      Attach the 7 hooks to install the actuator shield.

    14. B0040FHE02
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 3 hooks.

    15. Using hog ring pliers, install the upper part of the separate type front seatback cover to the separate type front seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    16. B0040ICE02
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the seatback cover bracket with the screw.

      Note

      After the separate type front seatback cover is installed, make sure the seatback cover bracket is not twisted.

    17. B0040P5

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

    18. A00560N

      Attach the 2 hooks to connect the 2 straps.

    19. B0040FP

      Attach the 2 hooks at the bottom of the separate type front seatback cover.

    20. Attach the 2 hooks.

      A00599S

  16. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY LH

    Tech Tips

    Perform this procedure when it is necessary to remove and reinstall or replace the separate type front seatback assembly LH.


    1. A00544P

      Using a T50 "TORX" socket wrench, install the separate type front seatback assembly LH to the front seat adjuster assembly LH with the 4 "TORX" bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }
    2. A0058QT

      Attach the 4 wire harness clamps.

    3. A0059A0

      Attach the connector.

    4. A00539Y

      Install the front seat headrest assembly.

      Note

      Push in the front seat headrest assembly until the headrest lock engages.

    5. A0055M9

      Pass the cable through the hole of the seatback frame.

    6. A0057YK

      Attach the 2 claws to install the clip.

    7. B0040NTE02
      Text in Illustration
      *1 Cable End

      Pull the cable through the clip until the cable end reaches the clip.

    8. A0058RD

      Install a new cable tie.

    9. B0040JKE02
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 2 hooks and close the seatback mat.

    10. Using hog ring pliers, install a new hog ring.

    11. A0058D2

      Attach the 2 claws to connect the cable to the active headrest lower unit.

    12. A00556Q

      Attach the 2 claws to install the active headrest lower unit.

    13. B0040PLE02
      Text in Illustration
      *1 Cable End
      A0054DN Pull

      Pull the cable and connect the cable end to the active headrest lower unit.

    14. A0056MF

      Attach the 7 hooks to install the actuator shield.

    15. B0040FHE02
      Text in Illustration
      *1 Hook
      *2 Hog Ring
      *3 Hog Ring Pliers

      Attach the 3 hooks.

    16. Using hog ring pliers, install the upper part of the separate type front seatback cover to the separate type front seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    17. B0040ICE02
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the seatback cover bracket with the screw.

      Note

      After the separate type front seatback cover is installed, make sure the seatback cover bracket is not twisted.

    18. A00557W

      for Driver Side:

      Connect the 2 connectors and attach the wire harness clamp.

    19. A00566B

      for Front Passenger Side:

      Connect the connector and attach the wire harness clamp.

    20. A0053L0

      Attach the wire harness clamp.

    21. B0040P5

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

    22. A00560N

      Attach the 2 hooks to connect the 2 straps.

    23. B0040FP

      Attach the 2 hooks at the bottom of the separate type front seatback cover.

    24. Attach the 2 hooks.

      A00599S

  17. INSTALL POWER SEAT MOTOR ASSEMBLY (for Rear Lifter)

    Click here

  18. INSTALL POWER SEAT MOTOR ASSEMBLY (for Front Vertical)

    Click here

  19. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH

    Click here

  20. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A00590Z

      Attach the hooks to install the separate type front seat cushion cover to the separate type front seat cushion pad.

      Note


      • Be careful not to damage the cover.

      • When attaching the hooks, avoid wrinkling the cover.

  21. INSTALL SEAT CUSHION COVER WITH PAD


    1. Attach the hooks to install the seat cushion cover with pad.

      A0058PQ

    2. Connect the 2 connectors.

    3. A0054WN

      for Driver Side:

      Attach the wire harness clamp.

    4. A00581E

      for Front Passenger Side:

      Attach the 2 hooks to connect the connector holder.

    5. A0054BM

      Install a new cable tie.

    6. A0059CZ

      Connect the connector.

  22. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    Click here

  23. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. B0040N9E02
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Attach the wire harness clamp and hook to install the front seat inner cushion shield LH.

    2. Install the 2 screws.

  24. INSTALL FRONT POWER SEAT SWITCH

    Click here

  25. INSTALL LUMBAR FRONT POWER SEAT SWITCH (for Driver Side)

    Click here

  26. INSTALL FRONT SEAT NO. 1 INNER CUSHION SHIELD LH


    1. B0040IR

      Attach the 2 claws to install the front seat No. 1 inner cushion shield to the front seat cushion shield LH.

  27. INSTALL FRONT SEAT CUSHION SHIELD LH WITH FRONT SEAT NO. 1 INNER CUSHION SHIELD LH


    1. B0040MJ

      for Driver Side:

      Connect the connector.

    2. B0040L8

      Attach the hook to install the front seat cushion shield LH with front seat inner No. 1 cushion shield.

    3. Install the 2 screws.

    4. B0040KK

      Attach the 2 claws and install the 2 screws.

    5. A0056LC

      Attach the 2 rubber bands.

  28. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. B0040IN

      Attach the 4 claws to install the slide and vertical power seat switch knob.

  29. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. B0040OH

      Attach the 2 claws to install the reclining power seat switch knob.