FRONT SEAT ASSEMBLY(for Manual Seat) DISASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. REMOVE VERTICAL SEAT ADJUSTER KNOB CAP (for Driver Side)


    1. B0040NXE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 3 claws and remove the vertical seat adjuster knob cap.

      Tech Tips

      Tape the screwdriver tip before use.

  2. REMOVE VERTICAL ADJUSTING HANDLE LH (for Driver Side)


    1. B0040JR

      Remove the 2 screws and vertical adjusting handle LH.

  3. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH


    1. B0040JQE02
      Text in Illustration
      *1 Protective Tape

      Raise the reclining adjuster release handle LH to reveal the claw. Using a screwdriver, detach the claw and remove the reclining adjuster release handle LH.

      Tech Tips

      Tape the screwdriver tip before use.

  4. REMOVE FRONT SEAT CUSHION SHIELD LH


    1. A0057XK

      Detach the 2 rubber bands.

    2. B0040PA

      Remove the 2 screws.

    3. Detach the hook and claw and remove the front seat cushion shield LH.

    4. B0040NO

      w/ Lumbar Support:

      Disconnect the connector.

  5. REMOVE LUMBAR FRONT POWER SEAT SWITCH (w/ Lumbar Support)

    Click here

  6. REMOVE FRONT SEAT INNER CUSHION SHIELD LH


    1. B0040IJE02
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Remove the 2 screws.

    2. Detach the hook and wire harness clamp and remove the front seat inner cushion shield LH.

  7. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH

    Click here

  8. REMOVE SEAT CUSHION COVER WITH PAD


    1. A0052QZ

      Remove the spring.

    2. A0052ER

      Using a 15 mm socket wrench, remove the nut and reclining handle.

    3. for Driver Side:


      1. B0040I5E02
        Text in Illustration
        *1 Connector Link

        Remove the clip and disconnect the connector link.

      2. B0040LME02
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, detach the 2 claws and remove the vertical adjuster handle bracket with connector link.

        Tech Tips

        Tape the screwdriver tip before use.

    4. w/ Seat Heater System:


      1. A0055PG

        Cut off the cable tie.

      2. A00596H

        Disconnect the connector.

    5. A00581E

      for Front Passenger Side:

      Detach the 2 hooks and disconnect the connector holder.

    6. A0054WN

      w/ Lumbar Support:

      Detach the wire harness clamp.

    7. w/ Seat Heater System:

      Disconnect the connector.

      B0040LFE02
      Text in Illustration
      *A w/ Seat Heater System - -

    8. Detach the hooks and remove the seat cushion cover with pad.

  9. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A00590Z

      Detach the hooks and remove the separate type front seat cushion cover from the separate type front seat cushion pad.

      Note

      w/ Seat Heater System:

      • As the front seat cushion heater assembly is affixed to the separate type front seat cushion pad, do not remove the front seat cushion heater assembly from the separate type front seat cushion pad.

      • When replacing either the front seat cushion heater assembly or separate type front seat cushion pad due to a malfunction, be sure to replace both of them with new parts.

  10. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

    Tech Tips

    Perform this procedure when it is necessary to remove and reinstall or replace the separate type front seatback assembly.


    1. B0040PKE02
      Text in Illustration
      *1 Protective Tape

      w/o Active Headrest:

      Using a screwdriver, push the headrest support lock to release the lock and remove the front seat headrest assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    2. w/ Lumbar Support:


      1. Detach the 2 hooks.

        A0053DG
      2. B0040FP

        Detach the 2 hooks from the bottom of the separate type front seatback cover.

      3. A0056UF

        Detach the 2 hooks and disconnect the 2 straps.

      4. B0040MC

        Pass the 2 straps through the 2 holes of the separate type front seatback pad to the surface.

      5. A0053L0

        Detach the wire harness clamp.

      6. A0056K1

        Disconnect the connector.

    3. w/ Active Headrest:


      1. B0040ICE02
        Text in Illustration
        *1 Seatback Cover Bracket

        Remove the screw and detach the seatback cover bracket.

      2. B0040GIE01
        Text in Illustration
        *1 Hook
        *2 Hog Ring

        Remove the hog rings and detach the 3 hooks from the center of the separate type front seatback pad.

      3. A0056MF

        Detach the 7 hooks and remove the actuator shield.

      4. B0040QDE02
        Text in Illustration
        *1 Cable End
        A0057VO Pull

        Pull the cable to loosen it, and then disconnect the cable end from the active headrest lower unit.

      5. A0058F0

        Detach the 2 claws and remove the active headrest lower unit.

      6. A0058D2

        Using a screwdriver, detach the 2 claws and disconnect the cable from the active headrest lower unit.

      7. B0040HHE02
        Text in Illustration
        *1 Hook
        *2 Hog Ring

        Remove the hog ring and detach the 2 hooks and open the seatback mat.

      8. A0058RD

        Cut off the cable tie.

      9. B0040NKE02
        Text in Illustration
        *1 Cable End

        Push the cable to push out the cable end from the clip.

      10. A0057YK

        Detach the 2 claws and remove the clip.

      11. A00558Q

        Pull the cable through the hole of the seatback frame.

      12. B0040J7E02
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, push the headrest support lock to release the lock and remove the front seat headrest assembly.

        Tech Tips

        Tape the screwdriver tip before use.

    4. A0057LV

      Detach the connector.

    5. A005679

      Detach the 2 wire harness clamps.

    6. Using a T50 "TORX" socket wrench, remove the 4 "TORX" bolts and separate type front seatback assembly from the front seat adjuster assembly LH.

  11. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    1. B0040PKE02
      Text in Illustration
      *1 Protective Tape

      w/o Active Headrest:

      Using a screwdriver, push the headrest support lock to release the lock and remove the front seat headrest assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Detach the 2 hooks.

      A0053DG
    3. B0040FP

      Detach the 2 hooks from the bottom of the separate type front seatback cover.

    4. A0056UF

      Detach the 2 hooks and disconnect the 2 straps.

    5. B0040MC

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the surface.

    6. B0040ICE02
      Text in Illustration
      *1 Seatback Cover Bracket

      Remove the screw and detach the seatback cover bracket.

    7. B0040GIE01
      Text in Illustration
      *1 Hook
      *2 Hog Ring

      Remove the hog rings and detach the 3 hooks from the center of the separate type front seatback pad.

    8. w/ Active headrest:


      1. A0056MF

        Detach the 7 hooks and remove the actuator shield.

      2. B0040QDE02
        Text in Illustration
        *1 Cable End
        A0057VO Pull

        Pull the cable to loosen it, and then disconnect the cable end from the active headrest lower unit.

      3. A0053IM

        Detach the 2 claws and remove the active headrest lower unit.

      4. A0058D2

        Using a screwdriver, detach the 2 claws and disconnect the cable.

      5. B0040HHE02
        Text in Illustration
        *1 Hook
        *2 Hog Ring

        Remove the hog ring and detach the 2 hooks and open the seatback mat.

      6. A0058RD

        Cut off the cable tie.

      7. B0040NKE02
        Text in Illustration
        *1 Cable End

        Push the cable to push out the cable end from the clip.

      8. A0057YK

        Detach the 2 claws and remove the clip.

      9. A00558Q

        Pull the cable through the hole of the seatback frame.

      10. B0040J7E02
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, push the headrest support lock to release the lock and remove the front seat headrest assembly.

        Tech Tips

        Tape the screwdriver tip before use.

    9. A00592R

      Detach the 2 claws and remove the 2 front seat headrest supports.

    10. A0052NQ

      Detach the 2 hooks and remove the separate type front seatback cover.

  12. REMOVE SEPARATE TYPE FRONT SEATBACK PAD

    A0052TM

    1. Remove the separate type front seatback pad.

      Note

      w/ Seat Heater System:

      • As the front seatback heater assembly is affixed to the separate type front seatback pad, do not remove the front seatback heater assembly from the separate type front seatback pad.

      • When replacing either the front seatback heater assembly or separate type front seatback pad due to a malfunction, be sure to replace both of them with new parts.

  13. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar Support)

    Click here

  14. REMOVE FRONT SEAT AIRBAG ASSEMBLY LH

    Click here

  15. REMOVE SEAT CLIMATE CONTROL CONTROLLER LH (w/ Seat Heater System)


    1. A0054PR

      Disconnect the connector.

    2. Detach the claw and remove the seat climate control controller LH.

  16. REMOVE FRONT SEAT WIRE LH (w/ Lumbar Support)


    1. A0053L0

      Detach the wire harness clamp.

    2. A005669

      Detach the 3 wire harness clamps.

    3. Detach the claw and remove the front seat wire LH.

  17. REMOVE FRONT SEAT LOWER CUSHION SHIELD LH

    A0058YC

    1. Remove the screw and front seat lower cushion shield LH.

  18. REMOVE FRONT SEAT INNER BELT ANCHOR BRACKET COVER LH

    A0057JP

    1. Remove the screw and front seat inner belt anchor bracket cover LH.

  19. REMOVE FRONT SEAT ADJUSTER ASSEMBLY LH


    1. A0053AV

      Using a T50 "TORX" socket wrench, remove the 4 "TORX" bolts and front seat adjuster assembly LH.

  20. REMOVE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

    B0040M0

    1. Detach the 8 hooks and remove the separate type front seat cushion spring assembly from the front seat adjuster assembly LH.

  21. REMOVE REAR UPPER SEAT TRACK COVER


    1. B0040PH

      Detach the 3 claws and remove the rear upper seat track cover.

  22. REMOVE NO. 2 REAR UPPER SEAT TRACK COVER


    1. B0040F2

      Detach the 3 claws and remove the No. 2 rear upper seat track cover.