AIRBAG SYSTEM, Diagnostic DTC:B1925/78, B1926/78, B1927/78, B1928/78

DTC Code DTC Name
B1925/78 Short in Rear Pretensioner Squib LH Circuit
B1926/78 Open in Rear Pretensioner Squib LH Circuit
B1927/78 Short to GND in Rear Pretensioner Squib LH Circuit
B1928/78 Short to B+ in Rear Pretensioner Squib LH Circuit

DESCRIPTION

The rear seat belt pretensioner LH circuit consists of the airbag sensor assembly and rear seat 3 point type outer belt assembly LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the rear seat belt pretensioner LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1925/78

One of the following conditions is met:


  • The airbag sensor assembly detects a line short circuit signal 5 times in the rear seat belt pretensioner LH circuit during the primary check.

  • A rear seat belt pretensioner LH malfunction.

  • An airbag sensor assembly malfunction.

  • Floor wire

  • Rear seat 3 point type outer belt assembly LH (Rear seat belt pretensioner LH)

  • Airbag sensor assembly
B1926/78

One of the following conditions is met:


  • The airbag sensor assembly detects an open circuit signal in the rear seat belt pretensioner LH circuit for 2 seconds.

  • A rear seat belt pretensioner LH malfunction.

  • An airbag sensor assembly malfunction.
B1927/78

One of the following conditions is met:


  • The airbag sensor assembly detects a short circuit to ground signal in the rear seat belt pretensioner LH circuit for 0.5 seconds.

  • A rear seat belt pretensioner LH malfunction.

  • An airbag sensor assembly malfunction.
B1928/78

One of the following conditions is met:


  • The airbag sensor assembly detects a short circuit to B+ signal in the rear seat belt pretensioner LH circuit for 0.5 seconds.

  • A rear seat belt pretensioner LH malfunction.

  • An airbag sensor assembly malfunction.

WIRING DIAGRAM

A00559GE07
*a Rear Seat 3 Point Type Outer Belt Assembly LH (Rear Seat Belt Pretensioner LH)
*b Airbag Sensor Assembly

CAUTION / NOTICE / HINT

Note


  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected Click here.

Tech Tips

To perform the simulation method, enter check mode (signal check) with the GTS (See page ), and then wiggle each connector of the airbag system or drive the vehicle on various types of road Click here.

PROCEDURE


  1. CHECK REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH (REAR SEAT BELT PRETENSIONER LH)


    1. A0053QYE02
      Text in Illustration
      *1 Rear Seat Belt Pretensioner LH
      *2 Airbag Sensor Assembly
      *3 Connector C
      *4 SST
      *a

      Front view of wire harness connector

      (to Rear Seat Belt Pretensioner LH)

      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Disconnect the connectors from the rear seat 3 point type outer belt assembly LH.

    4. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

      CAUTION:

      Never connect the tester to the rear seat 3 point type outer belt assembly LH (rear seat belt pretensioner LH) for measurement, as this may lead to a serious injury due to airbag deployment.

      Note


      • Do not forcibly insert SST into the terminals of the connector when connecting SST.

      • Insert SST straight into the terminals of the connector.

      SST
      09843-18061

    5. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Clear the DTCs Click here.

    8. Turn the ignition switch off.

    9. Turn the ignition switch to ON, and wait for at least 60 seconds.

    10. Check for DTCs Click here.

      OK
      DTC B1925/78, B1926/78, B1927/78 or B1928/78 is not output.
      Result
      Result Proceed to
      OK (for Sedan) A
      OK (for Wagon) B
      NG C

      Tech Tips

      Codes other than DTC B1925/78, B1926/78, B1927/78 and B1928/78 may be output at this time, but they are not related to this check.

    11. Turn the ignition switch off.

    12. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    13. Disconnect SST from connector C.


    A

    REPLACE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH Click here

    B

    REPLACE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH Click here

    C

  2. CHECK CONNECTORS


    1. Disconnect the connectors from the airbag sensor assembly.

    2. A0058WIE03
      Text in Illustration
      *1 Rear Seat Belt Pretensioner LH
      *2 Floor Wire
      *3 Airbag Sensor Assembly

      Check that the connectors (on the airbag sensor assembly side and rear seat 3 point type outer belt assembly LH side) are not damaged.

      OK
      The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

    NG

    REPLACE FLOOR WIRE

    OK

  3. CHECK FLOOR WIRE


    1. A0057WUE02
      Text in Illustration
      *1 Rear Seat Belt Pretensioner LH
      *2 Floor Wire
      *3 Airbag Sensor Assembly
      *4 Connector C
      *a

      Front view of wire harness connector

      (to Rear Seat Belt Pretensioner LH)

      Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G65-1 (RL+) - Body ground Ignition switch ON Below 1 V
      G65-2 (RL-) - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G65-1 (RL+) - G65-2 (RL-) Always Below 1 Ω

    7. Release the activation prevention mechanism built into connector B Click here.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G65-1 (RL+) - G65-2 (RL-) Always 1 MΩ or higher
      G65-1 (RL+) - Body ground Always 1 MΩ or higher
      G65-2 (RL-) - Body ground Always 1 MΩ or higher

    9. Restore the released activation prevention mechanism of connector B to its original condition.


    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK FOR DTC


    1. A0057UJE53
      Text in Illustration
      *1 Rear Seat Belt Pretensioner LH
      *2 Airbag Sensor Assembly

      Connect the connectors to the rear seat 3 point type outer belt assembly LH and airbag sensor assembly.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs Click here.

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      OK
      DTC B1925/78, B1926/78, B1927/78 or B1928/78 is not output.

      Tech Tips

      Codes other than DTC B1925/78, B1926/78, B1927/78 and B1928/78 may be output at this time, but they are not related to this check.


    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPLACE AIRBAG SENSOR ASSEMBLY Click here