AIRBAG SYSTEM, Diagnostic DTC:B1825/56, B1826/56, B1827/56, B1828/56

DTC Code DTC Name
B1825/56 Short in Side Squib LH Circuit
B1826/56 Open in Side Squib LH Circuit
B1827/56 Short to GND in Side Squib LH Circuit
B1828/56 Short to B+ in Side Squib LH Circuit

DESCRIPTION

The front side squib LH circuit consists of the airbag sensor assembly and front seat airbag assembly LH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front side squib LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1825/56

One of the following conditions is met:


  • The airbag sensor assembly detects a line short circuit signal 5 times in the front side squib LH circuit during the primary check.

  • A front side squib LH malfunction.

  • An airbag sensor assembly malfunction.

  • Floor wire

  • Front seat airbag assembly LH (Front side squib LH)

  • Airbag sensor assembly
B1826/56

One of the following conditions is met:


  • The airbag sensor assembly detects an open circuit signal in the front side squib LH circuit for 2 seconds.

  • A front side squib LH malfunction.

  • An airbag sensor assembly malfunction.
B1827/56

One of the following conditions is met:


  • The airbag sensor assembly detects a short circuit to ground signal in the front side squib LH circuit for 0.5 seconds.

  • A front side squib LH malfunction.

  • An airbag sensor assembly malfunction.
B1828/56

One of the following conditions is met:


  • The airbag sensor assembly detects a short circuit to B+ signal in the front side squib LH circuit for 0.5 seconds.

  • A front side squib LH malfunction.

  • An airbag sensor assembly malfunction.

WIRING DIAGRAM

A00589JE05
*a Front Seat Airbag Assembly LH (Front Side Squib LH)
*b Airbag Sensor Assembly

CAUTION / NOTICE / HINT

Note


  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected Click here.

Tech Tips

To perform the simulation method, enter check mode (signal check) with the GTS (See page ), and then wiggle each connector of the airbag system or drive the vehicle on various types of road Click here.

PROCEDURE


  1. CHECK FRONT SEAT AIRBAG ASSEMBLY LH (FRONT SIDE SQUIB LH)


    1. A0059B0E02
      Text in Illustration
      *1 Front Side Squib LH
      *2 Airbag Sensor Assembly
      *3 Connector E
      *4 SST
      *a

      Front view of wire harness connector

      (to Front Side Squib LH)
      *b Color: Red

      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Disconnect the connector from the front seat airbag assembly LH.

    4. Connect the red wire side of SST (resistance: 2.1 Ω) to connector E.

      CAUTION:

      Never connect the tester to the front seat airbag assembly LH (front side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

      Note


      • Do not forcibly insert SST into the terminals of the connector when connecting SST.

      • Insert SST straight into the terminals of the connector.

      SST
      09843-18061

    5. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Clear the DTCs Click here.

    8. Turn the ignition switch off.

    9. Turn the ignition switch to ON, and wait for at least 60 seconds.

    10. Check for DTCs Click here.

      OK
      DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output.

      Tech Tips

      Codes other than DTC B1825/56, B1826/56, B1827/56 and B1828/56 may be output at this time, but they are not related to this check.

    11. Turn the ignition switch off.

    12. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    13. Disconnect SST from connector E.


    OK

    REPLACE FRONT SEAT AIRBAG ASSEMBLY LH Click here

    NG

  2. CHECK CONNECTORS


    1. Disconnect the connectors from the airbag sensor assembly.

    2. A0054VME04
      Text in Illustration
      *1 Front Side Squib LH
      *2 Floor Wire
      *3 Airbag Sensor Assembly

      Check that the connectors (on the airbag sensor assembly side and front seat airbag assembly LH side) are not damaged.

      OK
      The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

    NG

    REPLACE FLOOR WIRE

    OK

  3. CHECK FLOOR WIRE


    1. A0058IYE02
      Text in Illustration
      *1 Front Side Squib LH
      *2 Floor Wire
      *3 Airbag Sensor Assembly
      *4 Connector C
      *a

      Front view of wire harness connector

      (to Front Side Squib LH)

      Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G15-1 (SFL+) - Body ground Ignition switch ON Below 1 V
      G15-2 (SFL-) - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G15-1 (SFL+) - G15-2 (SFL-) Always Below 1 Ω

    7. Release the activation prevention mechanism built into connector B Click here.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G15-1 (SFL+) - G15-2 (SFL-) Always 1 MΩ or higher
      G15-1 (SFL+) - Body ground Always 1 MΩ or higher
      G15-2 (SFL-) - Body ground Always 1 MΩ or higher

    9. Restore the released activation prevention mechanism of connector B to its original condition.


    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK FOR DTC


    1. A0057UJE53
      Text in Illustration
      *1 Front Side Squib LH
      *2 Airbag Sensor Assembly

      Connect the connectors to the front seat airbag assembly LH and airbag sensor assembly.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs Click here.

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      OK
      DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output.

      Tech Tips

      Codes other than DTC B1825/56, B1826/56, B1827/56 and B1828/56 may be output at this time, but they are not related to this check.


    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPLACE AIRBAG SENSOR ASSEMBLY Click here