FUEL INJECTOR INSPECTION

PROCEDURE


  1. INSPECT FUEL INJECTOR ASSEMBLY


    1. A00551GE01
      Text in Illustration
      *1

      Component without harness connected

      (Fuel Injector Assembly)

      Check the resistance.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        1 - 2 20°C (68°F) 11.6 to 12.4 Ω

        If the result is not as specified, replace the injector assembly.

    2. Check the injection volume.

      CAUTION:

      Perform the inspection in a well-ventilated area.

      Do not perform the inspection near any naked flames.


      1. A0053SZE04
        Text in Illustration
        *1 Fuel Pipe
        *a SST (Fuel Tube Connector)
        *b SST (Hose)
        *c SST (Hose Band)

        Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel pipe (vehicle side).

        SST
        09268-31014   ( 09268-41500, 09268-41700, 95336-08070 )
      2. A005865E02
        Text in Illustration
        *1 O-Ring
        *2 Vinyl Tube
        *a SST (Hose Band)
        *b SST (Adapter)
        *c SST (Hose)
        *d SST (Clamp)

        Install the O-ring onto the fuel injector assembly.

      3. Connect SST (adapter and hose) to the injector assembly, and hold the injector assembly and union with SST (clamp).

        SST
        09268-31014   ( 09268-41110, 09268-41300, 09268-41700, 95336-08070 )
      4. A0058AQE02
        Text in Illustration
        *1 Lock
        *a SST (Tie Band)

        Pass SST (tie band) through the loop on the handle of SST (clamp) to secure SST (clamp) to SST (adapter).

        SST
        09268-31014   ( 09268-41800 )

        Note


        • As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.

        • Before using SST (tie band), make sure that there is no deterioration, damage or cracks. If there are any abnormalities, replace SST.

        Tech Tips

        When removing SST (tie band), disengage the lock.

      5. Check that SST (clamp) and SST (adapter) cannot be easily separated.

      6. Install a vinyl tube onto the injector.

        CAUTION:

        Install a suitable vinyl tube onto the injector to prevent gasoline from splashing out.

      7. Put the injector into a graduated cylinder.

      8. Operate the fuel pump Click here.

      9. A00580LE02

        Connect SST (wire) to the injector and battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each injector 2 or 3 times.

        SST
        09842-30080
        Standard injection volume
        60 to 73 cc (3.7 to 4.5 cu. in.) per 15 seconds
        Difference between each injector
        13 cc (0.8 cu. in.) or less
        Text in Illustration
        A0054DN Connect

        Note

        Always do the switching at the battery side.

        If the injection volume is not as specified, replace the injector assembly.

    3. A0054SP

      Inspect for fuel leak.


      1. In the condition above, disconnect the test probes of SST (wire) from the battery and check the fuel leakage from the injector.

        Fuel drop
        1 drop or less every 12 minutes