CAMSHAFT INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips

Perform "Inspection After Repairs" after replacing the camshaft housing sub-assembly, camshaft timing gear assembly or camshaft timing exhaust gear assembly Click here.

PROCEDURE


  1. INSTALL VALVE LASH ADJUSTER ASSEMBLY

    Click here

  2. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

    Click here

  3. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

    Tech Tips

    Perform "Inspection After Repairs" after replacing the camshaft housing sub-assembly Click here.


    1. A0057DGE04
      Text in Illustration
      *1 Lash Adjuster
      *2 Valve Rocker Arm
      *3 Valve Stem
      *4 Valve Stem Cap

      Make sure that the valve rocker arms are installed as shown in the illustration.

    2. A0052R1E14
      *1 7.0 mm
      *2 8.0 mm
      *3 3.5 to 4.5 mm

      Apply seal packing in a continuous line as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Standard Seal Diameter
      Area Specified Condition
      Continuous Line 3.5 to 4.5 mm (0.138 to 0.177 in.)
      A 8.0 mm (0.315 in.)
      B 7.0 mm (0.276 in.)
      Application Length A and B
      15 mm (0.591 in.)

      Note


      • Remove any oil from the contact surfaces.

      • Install the camshaft housing within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

      • Do not start the engine for at least 2 hours after installation.

    3. A0057VGE05

      Set the camshaft and No. 2 camshaft as shown in the illustration.

    4. Install the camshaft housing with the 17 bolts and tighten them in the order shown in the illustration.

      Torque:
      27 N*m  { 275 kgf*cm, 20 ft.*lbf }

      Note


      • After installing the camshaft housing, make sure that the cam lobes are positioned as shown in the illustration.

      • If any of the bolts are loosened during installation, remove the camshaft housing, clean the installation surfaces, and reapply seal packing.

      • If the camshaft housing is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.

      • After installing the camshaft housing, wipe off any seal packing that seeped out from between the housing and cylinder head.

  4. INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

    Tech Tips

    Perform "Inspection After Repairs" after replacing the camshaft timing exhaust gear assembly Click here.


    1. A00550GE01
      Text in Illustration
      *1 Straight Pin
      *2 Pin Hole

      Put the camshaft timing exhaust gear and camshaft together by aligning the pin hole and straight pin.

      Note

      Do not forcefully push in the camshaft timing exhaust gear. This may cause the camshaft straight pin tip to damage the installation surface of the camshaft timing exhaust gear.

    2. Lightly press the gear against the camshaft and turn the gear. Push further at the position where the pin enters the hole.

      Note

      Be sure not to turn the camshaft timing exhaust gear in the retard direction (clockwise).

    3. A00569LE25
      *1 Camshaft Timing Gear
      *2 Clearance
      *3 Flange
      *4 No Clearance

      Check that there is no clearance between the gear and camshaft flange.

    4. A0057AY

      Tighten the flange bolt with the camshaft timing exhaust gear secured in place.

      Torque:
      54 N*m  { 551 kgf*cm, 40 ft.*lbf }

    5. Check the camshaft timing exhaust gear lock.


      1. Make sure that the camshaft timing exhaust gear is locked.

  5. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

    Tech Tips

    Perform "Inspection After Repairs" after replacing the camshaft timing gear assembly Click here.


    1. A005956E02
      Text in Illustration
      *1 Straight Pin
      *2 Key Groove

      Put the camshaft timing gear and camshaft together with the straight pin and key groove misaligned as shown in the illustration.

      Note

      Do not forcefully push in the camshaft timing gear. This may cause the camshaft straight pin tip to damage the installation surface of the camshaft timing gear.

    2. A005964E02
      Text in Illustration
      *1 Straight Pin
      *2 Key Groove

      Turn the camshaft timing gear as shown in the illustration while pushing it gently against the camshaft. Push further at the position where the pin fits into the groove.

      Note

      Do not turn the camshaft timing gear in the retard direction (clockwise).

    3. A00569LE25
      *1 Camshaft Timing Gear
      *2 Clearance
      *3 Flange
      *4 No Clearance

      Check that there is no clearance between the camshaft timing gear and camshaft flange.

    4. A0059GZ

      Tighten the flange bolt with the camshaft timing gear secured in place.

      Torque:
      54 N*m  { 551 kgf*cm, 40 ft.*lbf }
    5. A0058CEE03
      Text in Illustration
      *1 Lock

      Check that the camshaft timing gear can move in the retard direction (clockwise) and is locked in the most retarded position.

  6. INSTALL NO. 1 CHAIN VIBRATION DAMPER


    1. A0055HP

      Install the chain vibration damper with the 2 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  7. SET NO. 1 CYLINDER TO TDC/COMPRESSION


    1. A0058A3E02
      Text in Illustration
      *1 Timing Gear Key

      Temporarily install the crankshaft pulley bolt.

    2. Turn the crankshaft counterclockwise to position the timing gear key at the top.

    3. A00539IE02
      Text in Illustration
      *1 Timing Mark

      Check that the timing marks on the camshaft timing gears are aligned as shown in the illustration.

    4. Remove the crankshaft pulley bolt.

  8. INSTALL CHAIN SUB-ASSEMBLY


    1. Align the mark plate (orange) with the timing mark as shown in the illustration and install the chain.

      A0052Z9E01
      Text in Illustration
      *1 Mark Plate (Orange)
      *2 Timing Mark

      Tech Tips


      • Be sure to position the mark plate at the front of the engine.

      • The mark plate on the camshaft side is colored orange.

      • Do not pass the chain around the sprocket of the camshaft timing gear. Only place it on the sprocket.

      • Pass the chain through the No. 1 vibration damper.

    2. Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear counterclockwise to align the mark plate (orange) and timing mark, and then install the chain.

    3. Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear clockwise.

      Tech Tips

      To tension the chain, slowly turn the camshaft timing gear clockwise to prevent the chain from being misaligned.

    4. A0052NPE07
      Text in Illustration
      *1 Timing Mark
      *2 Mark Plate (Yellow or Pink)

      Align the mark plates (yellow or pink) and timing marks and install the chain to the crankshaft timing gear.

      Tech Tips

      The mark plates on the crankshaft side are colored yellow or pink.

  9. INSTALL CHAIN TENSIONER SLIPPER


    1. A0056LF

      Install the chain tensioner slipper to the cylinder block.

  10. CHECK NO. 1 CYLINDER TO TDC/COMPRESSION


    1. Check each timing mark at TDC/compression.

      A0058YZE01
      Text in Illustration
      *1 Timing Mark *2 Mark Plate (Orange)
      *3 Mark Plate (Yellow or Pink) -

  11. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

    Click here

  12. INSTALL TIMING CHAIN COVER OIL SEAL

    Click here

  13. INSTALL CRANKSHAFT PULLEY

    Click here

  14. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY


    1. A0058GGE01

      Release the cam, and then fully push in the plunger and engage the hook to the pin so that the plunger is in the position shown in the illustration.

      Note

      Make sure that the cam engages the first tooth of the plunger to allow the hook to pass over the pin.

    2. A0055J4

      Install a new gasket, the chain tensioner and bracket with the 2 nuts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

      Note

      If the hook releases the plunger while the chain tensioner is being installed, set the hook again.

    3. A0053T5E08
      Text in Illustration
      *1 Release
      *2 Pin
      *3 Hook
      *4 Turn

      Rotate the crankshaft counterclockwise slightly and check that the hook becomes released.

    4. A0052POE01
      Text in Illustration
      *1 Plunger
      *2 Plunger Extended
      *3 Turn

      Turn the crankshaft clockwise and check that the plunger is extended.

  15. INSTALL SPARK PLUG TUBE GASKET

    Click here

  16. INSTALL CYLINDER HEAD COVER GASKET

    Click here

  17. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

    Click here

  18. INSTALL RADIO SETTING CONDENSER

    Click here

  19. INSTALL IGNITION COIL ASSEMBLY

    Click here

  20. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

    Click here

  21. INSTALL NO. 1 VACUUM PUMP BRACKET

    Click here

  22. INSTALL VACUUM PUMP ASSEMBLY

    Click here

  23. INSTALL THERMOSTAT

    Click here

  24. INSTALL WATER INLET

    Click here

  25. INSTALL WATER INLET HOSE

    Click here

  26. CONNECT NO. 3 WATER BY-PASS HOSE

    Click here

  27. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

    Click here

  28. INSTALL FUEL INJECTOR ASSEMBLY

    Click here

  29. INSTALL NO. 1 DELIVERY PIPE SPACER

    Click here

  30. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

    Click here

  31. INSTALL FUEL TUBE SUB-ASSEMBLY

    Click here

  32. INSTALL WIRE HARNESS CLAMP BRACKET

    Click here

  33. INSTALL AIR TUBE

    Click here

  34. INSTALL INTAKE MANIFOLD

    Click here

  35. INSTALL THROTTLE BODY ASSEMBLY

    Click here

  36. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE


    1. Install the engine assembly with transaxle Click here.