SFI SYSTEM, Diagnostic DTC:P0351, P0352, P0353, P0354

DTC Code DTC Name
P0351 Ignition Coil "A" Primary / Secondary Circuit
P0352 Ignition Coil "B" Primary / Secondary Circuit
P0353 Ignition Coil "C" Primary / Secondary Circuit
P0354 Ignition Coil "D" Primary / Secondary Circuit

DESCRIPTION

A Direct Ignition System (DIS) is used on this vehicle to enhance ignition accuracy and suppress high voltage losses.

The DIS is an ignition system in which each cylinder is ignited by one ignition coil assembly. The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Based on the IGT signals, the ECM turns the power transistor inside the igniter on and off, turning the current to the primary coil on and off. When the current to the primary coil is cut off, a voltage is generated in the secondary coil and then applied to the spark plugs, causing them to spark inside the cylinders. At the same time, the igniter sends back the ignition confirmation (IGF) signal to the ECM.

A005857E07
DTC No. DTC Detection Condition Trouble Area

P0351

P0352

P0353

P0354

 No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).

  • Ignition system

  • Open or short in IGF1 or IGT (1 to 4) circuit between ignition coil and ECM

  • No. 1 to No. 4 ignition coils

  • ECM

WIRING DIAGRAM

A0059MEE01
A00536XE02

CAUTION / NOTICE / HINT

Tech Tips


  • The following inspection procedure is for the No. 1 cylinder. If any of the other cylinders are malfunctioning, inspect their circuits by referring to the following procedure.

  • If DTC P0351 is output, check the ignition coil assembly No. 1 circuit.

  • If DTC P0352 is output, check the ignition coil assembly No. 2 circuit.

  • If DTC P0353 is output, check the ignition coil assembly No. 3 circuit.

  • If DTC P0354 is output, check the ignition coil assembly No. 4 circuit.

  • Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK DTC OUTPUT


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / DTC.

    5. Read the DTCs.

      Result
      Result Proceed to
      DTC P0351, P0352, P0353 or P0354 is output A
      DTC P0351, P0352, P0353 and P0354 are output B

    B

    CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND) Click here

    A

  2. CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the tester on.

    4. Clear the DTCs Click here.

    5. Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).

      Note

      Do not shuffle the connectors.

    6. Perform a simulation test.

    7. Check the DTCs output to the tester.

      Result
      Result Proceed to
      Same DTC output A
      Different ignition coil assembly DTC output B

    B

    REPLACE IGNITION COIL ASSEMBLY Click here

    A

  3. CHECK IGNITION COIL ASSEMBLY (POWER SOURCE)


    1. A0054SXE02
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Ignition Coil Assembly)

      Disconnect the ignition coil assembly connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      B28-1 (+B) - B28-4 (GND) Ignition switch ON 11 to 14 V
      B29-1 (+B) - B29-4 (GND) Ignition switch ON 11 to 14 V
      B30-1 (+B) - B30-4 (GND) Ignition switch ON 11 to 14 V
      B31-1 (+B) - B31-4 (GND) Ignition switch ON 11 to 14 V

    3. Reconnect the ignition coil assembly connectors.


    NG

    CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - INTEGRATION RELAY (IGT/INJ RELAY)) Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)


    1. Disconnect the ignition coil assembly connectors.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      B28-2 (IGF) - B39-82 (IGF1) Always Below 1 Ω
      B29-2 (IGF) - B39-82 (IGF1) Always Below 1 Ω
      B30-2 (IGF) - B39-82 (IGF1) Always Below 1 Ω
      B31-2 (IGF) - B39-82 (IGF1) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      B28-2 (IGF) or B39-82 (IGF1) - Body ground Always 10 kΩ or higher
      B29-2 (IGF) or B39-82 (IGF1) - Body ground Always 10 kΩ or higher
      B30-2 (IGF) or B39-82 (IGF1) - Body ground Always 10 kΩ or higher
      B31-2 (IGF) or B39-82 (IGF1) - Body ground Always 10 kΩ or higher

    4. Reconnect the ECM connector.

    5. Reconnect the ignition coil assembly connectors.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

    OK

  5. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)


    1. Disconnect the ignition coil assembly connectors.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      B28-3 (IGT1) - B39-109 (IGT1) Always Below 1 Ω
      B29-3 (IGT2) - B39-108 (IGT2) Always Below 1 Ω
      B30-3 (IGT3) - B39-107 (IGT3) Always Below 1 Ω
      B31-3 (IGT4) - B39-106 (IGT4) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      B28-3 (IGT1) or B39-109 (IGT1) - Body ground Always 10 kΩ or higher
      B29-3 (IGT2) or B39-108 (IGT2) - Body ground Always 10 kΩ or higher
      B30-3 (IGT3) or B39-107 (IGT3) - Body ground Always 10 kΩ or higher
      B31-3 (IGT4) or B39-106 (IGT4) - Body ground Always 10 kΩ or higher

    4. Reconnect the ECM connector.

    5. Reconnect the ignition coil assembly connectors.


    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

  6. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)


    1. A0052GIE02
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Ignition Coil Assembly)

      Disconnect the ignition coil assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B28-4 (GND) - Body ground Always Below 1 Ω
      B29-4 (GND) - Body ground Always Below 1 Ω
      B30-4 (GND) - Body ground Always Below 1 Ω
      B31-4 (GND) - Body ground Always Below 1 Ω

    3. Reconnect the ignition coil assembly connectors.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)

    OK

  7. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - INTEGRATION RELAY (IGT/INJ RELAY))


    1. Disconnect the ignition coil assembly connectors.

    2. Remove the integration relay from the engine room No. 1 relay block.

    3. Disconnect the integration relay connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      B28-1 (+B) - 1B-8 Always Below 1 Ω
      B29-1 (+B) - 1B-8 Always Below 1 Ω
      B30-1 (+B) - 1B-8 Always Below 1 Ω
      B31-1 (+B) - 1B-8 Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      B28-1 (+B) or 1B-8 - Body ground Always 10 kΩ or higher
      B29-1 (+B) or 1B-8 - Body ground Always 10 kΩ or higher
      B30-1 (+B) or 1B-8 - Body ground Always 10 kΩ or higher
      B31-1 (+B) or 1B-8 - Body ground Always 10 kΩ or higher

    5. Reconnect the integration relay connector.

    6. Reinstall the integration relay.

    7. Reconnect the ignition coil assembly connectors.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - INTEGRATION RELAY (IGT/INJ RELAY))

    OK

  8. INSPECT INTEGRATION RELAY (IGT/INJ RELAY)


    1. A0058JWE02
      Text in Illustration
      *1 Engine Room No. 1 Relay Block
      *2

      Component without harness connected

      (Integration Relay)

      Remove the integration relay from the engine room No. 1 relay block.

    2. Disconnect the integration relay connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1C-1 - 1B-8 Battery voltage not applied to terminals 1B-6 and 1B-7 10 kΩ or higher
      Battery voltage applied to terminals 1B-6 and 1B-7 Below 1 Ω

    4. Reconnect the integration relay connector.

    5. Reinstall the integration relay.


    NG

    REPLACE INTEGRATION RELAY Click here

    OK

  9. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY (IGT/INJ RELAY) - INTEGRATION RELAY (EFI MAIN RELAY), BODY GROUND)


    1. Remove the integration relay from the engine room No. 1 relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      1B-4 - 1B-6 Always Below 1 Ω
      1B-7 - Body ground Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      1B-4 or 1B-6 - Body ground Always 10 kΩ or higher

    3. Reconnect the integration relay connector.

    4. Reinstall the integration relay.


    OK

    CHECK ECM POWER SOURCE CIRCUIT Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY (EFI MAIN RELAY) - INTEGRATION RELAY (IGT/INJ RELAY), BODY GROUND)