SFI SYSTEM, Diagnostic DTC:P2119

DTC Code DTC Name
P2119 Throttle Actuator Control Throttle Body Range / Performance

DESCRIPTION

The electronic throttle control system is composed of the throttle actuator, throttle position sensor, accelerator pedal position sensor, and ECM. The ECM operates the throttle actuator to regulate the throttle valve in response to driver inputs. The throttle position sensor detects the opening angle of the throttle valve, and provides the ECM with feedback so that the throttle valve can be appropriately controlled by the ECM.

DTC No. DTC Detection Condition Trouble Area
P2119 Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic).

  • Electronic throttle control system

  • ECM

  • Wire harness or connector

FAIL-SAFE

When this DTC, as well as other DTCs relating to electronic throttle control system malfunctions, is stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 5.5° opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal position, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed gently, the vehicle can be driven slowly. Fail-safe mode continues until a pass condition is detected and the ignition switch is turned off.

WIRING DIAGRAM

Refer to DTC P2102 Click here.

CAUTION / NOTICE / HINT

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2119)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    5. Read the DTCs.

      Result
      Result Proceed to
      DTC P2119 is output A
      DTC P2119 and other DTCs are output B

      Tech Tips

      If any DTCs other than P2119 are output, troubleshoot those DTCs first.


    B

    GO TO DTC CHART Click here

    A

  2. READ VALUE USING GTS (THROTTLE POSITION)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs Click here.

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON.

    7. Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position Command.

    8. Check the values displayed on the GTS while fully depressing and releasing the accelerator pedal quickly.

      Result
      Result Proceed to
      Throttle Position No. 1 does not change A
      Throttle Position No. 1 changes even a little B

      Tech Tips

      When a DTC is output, the system changes to fail-safe mode. Therefore, only use the data up until the time the DTC is stored for confirmation.


    B

    INSPECT THROTTLE BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE) Click here

    A

  3. INSPECT THROTTLE BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)


    1. Inspect the throttle body assembly Click here.


    NG

    REPLACE THROTTLE BODY ASSEMBLY Click here

    OK

  4. INSPECT THROTTLE BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)


    1. Check for contamination between the throttle valve and housing. If necessary, clean the throttle body assembly. Also, check that the throttle valve moves smoothly.

      OK
      Throttle valve is not contaminated with foreign objects and moves smoothly.

    NG

    REPLACE THROTTLE BODY ASSEMBLY Click here

    OK

  5. READ VALUE USING GTS (THROTTLE POSITION)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs Click here.

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON.

    7. Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.

    8. Check the values displayed on the GTS while wiggling the ECM wire harness.

    9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    10. Check for DTCs.

      Result
      Result Proceed to
      Value in Data List changes when wire harness is wiggled, or DTC is output A
      Other than above B

    B

    CHECK WHETHER DTC OUTPUT RECURS (DTC P2119) Click here

    A

  6. REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE BODY ASSEMBLY)


    1. As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector Click here.


    NEXT

    END

  7. REPLACE THROTTLE BODY ASSEMBLY


    1. Replace the throttle body assembly Click here.

      Tech Tips

      Perform "Inspection After Repair" after replacing the throttle body assembly Click here.


    NEXT

  8. CHECK WHETHER DTC OUTPUT RECURS (DTC P2119)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs Click here.

    5. Allow the engine to idle for 15 seconds or more.

    6. Fully depress and release the accelerator pedal several times quickly.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    8. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC P2119 is output B

    A

    END

    B

    REPLACE ECM Click here