3ZR-FE ENGINE MECHANICAL TORQUE SPECIFICATIONS

ENGINE
Part Tightened N*m kgf*cm ft.*lbf
Spark plug x Cylinder head 20 204 15
Ignition coil x Cylinder head cover 10 102 7
DRIVE BELT
Part Tightened N*m kgf*cm ft.*lbf
Generator x Timing chain cover, Adjusting bar for bolt A 19 194 14
for bolt B 43 438 32
CAMSHAFT
Part Tightened N*m kgf*cm ft.*lbf
Camshaft bearing cap x Camshaft housing 16 163 12
Camshaft housing x Cylinder head 27 275 20
Camshaft timing exhaust gear x No. 2 camshaft 54 551 40
Camshaft timing gear x camshaft 54 551 40
No. 1 chain vibration damper x Cylinder block, Cylinder head 21 214 15
No. 2 chain vibration damper x Camshaft housing 10 102 7
No. 1 chain tensioner x Timing chain cover 12 122 9
CYLINDER HEAD GASKET
Part Tightened N*m kgf*cm ft.*lbf
Cylinder head x Cylinder block 1st 49 500 36
2nd Turn 90° Turn 90° Turn 90°
3rd Turn 45° Turn 45° Turn 45°
FRONT CRANKSHAFT OIL SEAL
Part Tightened N*m kgf*cm ft.*lbf
Crankshaft pulley x Crankshaft 190 1940 140
REAR CRANKSHAFT OIL SEAL
Part Tightened N*m kgf*cm ft.*lbf
Drive plate and ring gear x Crankshaft 88 897 65
ENGINE ASSEMBLY
Part Tightened N*m kgf*cm ft.*lbf
No. 1, No. 2 engine hanger x Cylinder head 43 438 32
Engine mounting insulator LH x Body 95 969 70
Engine mounting insulator RH x Body 95 969 70
Cooler pipe bracket x Engine mounting insulator RH 9.8 100 87 in.*lbf
Rear engine mounting insulator x Front suspension crossmember 95 969 70
Front engine mounting insulator x Front crossmember 95 969 70
Engine mounting insulator LH x Engine mounting bracket 56 571 41
Engine mounting insulator RH x Engine mounting bracket RH for bolt and nut A 95 969 70
for nut B 52 530 38
Front suspension crossmember x Body 137 1397 101
Front suspension member brace rear LH, RH x Body for bolt A 137 1397 101
for bolt B 93 948 69
Air fuel ratio sensor bracket x Cylinder head 60 612 44
Front crossmember x Body 99 1010 73
Front engine mounting insulator x Front engine mounting bracket 145 1479 107
Rear engine mounting insulator x Rear engine mounting bracket 95 969 70
Front suspension member reinforcement LH x Front suspension crossmember, Body 99 1010 73
Front suspension member reinforcement RH x Front suspension crossmember, Body 99 1010 73
Engine wire x Cylinder head 29 296 21
Engine wire x Body 8.4 86 74 in.*lbf
Wire harness x Engine room No. 1 junction block 8.4 86 74 in.*lbf
Transmission control cable bracket x Front suspension crossmember 5.0 51 44 in.*lbf
Transmission control cable x Control shaft lever 12 122 9
Battery carrier x Body 19 189 14
Battery clamp x Body for bolt 17 168 12
for nut 3.5 36 31 in.*lbf
Positive (+) battery terminal x Battery 5.4 55 48 in.*lbf
Compressor with pulley stud bolt 9.8 100 87 in.*lbf
Compressor with pulley x Timing chain cover, Cylinder block 25 255 18
Radiator reservoir x Body 5.0 51 44 in.*lbf
ENGINE UNIT
Part Tightened N*m kgf*cm ft.*lbf
Stiffening crankcase stud bolt 5.0 51 44 in.*lbf
Stiffening crankcase x Cylinder block 21 214 15
Oil pan drain plug x No. 2 oil pan 37 377 27
No. 1 taper screw plug x Cylinder block Plug A 25 255 18
Plug B 43 438 32
No. 1 generator bracket x Cylinder block 24 245 18
Water inlet housing stud bolt 5.0 51 44 in.*lbf
Water inlet housing x Timing chain cover 21 214 15
Engine mounting bracket stud bolt 10 102 7
Oil filter union x Oil filter bracket 30 301 22
Cylinder head cover x Camshaft housing 10 102 7
Engine coolant temperature sensor x Cylinder head 20 204 15
Crankshaft position sensor x Timing chain cover 10 102 7
Knock sensor x Cylinder block 21 214 15
Camshaft timing oil control valve x Cylinder head cover 10 102 7
Camshaft position sensor x Cylinder head cover 10 102 7
Engine cover joint x cylinder head cover 10 102 7
Radio setting condenser x Cylinder head cover 10 102 7
No. 1 water by-pass pipe x Cylinder head 21 214 15
Drive shaft bearing bracket x Cylinder block 64 650 47
Engine oil level dipstick guide x No. 1 generator bracket 21 214 15
CYLINDER HEAD
Part Tightened N*m kgf*cm ft.*lbf
Cylinder head stud bolt 9.5 97 84 in.*lbf
No. 2 straight screw plug x Cylinder head 44 449 32
CYLINDER BLOCK
Part Tightened N*m kgf*cm ft.*lbf
Cylinder block stud bolt 5.0 51 44 in.*lbf
No. 1 oil nozzle x Cylinder block 10 102 7
Crankshaft bearing cap x Cylinder block 1st 40 408 30
2nd Turn 90° Turn 90° Turn 90°
Connecting rod bearing cap x Connecting rod 1st 20 204 15
2nd Turn 90° Turn 90° Turn 90°
No. 1 ventilation case x Cylinder block 10 102 7