TRANSMISSION CONTROL CABLE INSTALLATION

PROCEDURE


  1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

    Note

    Before installing the transmission control cable assembly, check that the park/neutral position switch and shift lever are in neutral.


    1. A0057JC

      Put the transmission control cable into the cabin and connect the transmission control cable with the 2 nuts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    2. A0058FQ

      Connect the transmission control cable support with the bolt.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    3. A0055XH

      Connect the transmission control cable to the control cable support.

    4. A0052EX

      Connect the transmission control cable to the bracket with a new clip.

    5. Connect the transmission control cable to the control shaft lever with the nut.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    6. Turn the nut of the transmission control cable 180° counterclockwise. While holding the nut in place, push in the stopper until the stopper clicks twice.

      A00589HE24
      Text in Illustration
      *1 Stopper *2 Nut

    7. Install the outer part of the transmission control cable to the shift lever retainer. Check that the spring is positioned at "A" and push in the stopper.

      A0059DZE10
      Text in Illustration
      *1 Stopper *3 Shift Lever Retainer
      *2 Nut *4 Spring

      Tech Tips

      If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.

    8. A0053WVE02
      *1 Side View:
      *2 Push
      *3 Bottom View:
      *4 Lock Piece

      Push the 2 claws together at the top of the transmission control cable lock piece. While holding the 2 claws together, push the 2 lugs on the bottom of the lock piece toward each other and upward to pull out the lock piece.

    9. A0055MCE02
      Text in Illustration
      *1 Lock Piece

      Connect the end of the cable to the shift lever assembly.

      Note


      • Make sure that the lock piece is pulled up.

      • Push on the end of the cable all the way to the base of the pin.

    10. A0053JWE02
      Text in Illustration
      *1 Lock Piece
      *2 Adjuster Case

      Push the lock piece into the adjuster case.

      Note

      Securely push in the lock piece until it locks.

  2. INSTALL FRONT FLOOR NO. 1 HEAT INSULATOR

    A0053XU

    1. Install the heat insulator with the 5 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  3. INSTALL FRONT EXHAUST PIPE ASSEMBLY

    Click here

  4. CONNECT HEATED OXYGEN SENSOR CONNECTOR

  5. INSTALL NO. 2 ENGINE UNDER COVER

    Click here

  6. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  7. INSTALL AIR CLEANER CAP AND HOSE

    Click here

  8. INSTALL BATTERY CARRIER

    Click here

  9. INSTALL BATTERY

    Click here

  10. INSTALL NO. 2 CYLINDER HEAD COVER

    Click here

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  12. INSTALL RADIATOR SUPPORT OPENING COVER

    Click here

  13. INSPECT SHIFT LEVER POSITION

    Click here

  14. ADJUST SHIFT LEVER POSITION

    Click here

  15. INSTALL CONSOLE BOX ASSEMBLY


    1. Install the console box assembly Click here