MANUAL TRANSAXLE UNIT REASSEMBLY

PROCEDURE


  1. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


    1. B0040O4E01

      Using SST and a press, install a new front differential case front tapered roller bearing to the differential case.

      SST
      09309-37010
      09506-35010
    2. B0040LQE01

      Using SST and a press, install the front differential case front tapered roller bearing (outer race) together with the front differential case front plate washer to the front transaxle case.

      SST
      09950-60020   ( 09951-00680 )
      09950-70010   ( 09951-07200 )

  2. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING


    1. B0040G3E01

      Using SST and a press, install a new front differential case rear tapered roller bearing to the differential case.

      SST
      09636-20010
      09726-40010
    2. B0040NZE11

      Using SST and a press, install the front differential case rear tapered roller bearing (outer race) together with the front differential case rear plate washer to the manual transmission case.

      SST
      09309-36010
      09950-60020   ( 09951-00730 )
      09950-70010   ( 09951-07100 )

  3. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD


    1. B0040K3

      Coat the differential case assembly with gear oil and install it to the front transaxle case.

    2. Install the manual transmission case with the 16 bolts.

      Torque:
      29 N*m  { 300 kgf*cm, 22 ft.*lbf }
    3. B0040QJE04
      Text in Illustration
      *1 Plate Washer

      Using SST and a torque wrench, turn the differential case assembly clockwise and counterclockwise 2 or 3 times to allow the bearings to settle.

      SST
      09564-32011

    4. Using SST and a torque wrench, measure the preload.

      SST
      09564-32011
      Standard preload (at starting)
      New bearing
      0.98 to 1.69 N*m (10 to 17 kgf*cm, 9 to 14 in.*lbf)
      Used bearing
      0.80 to 1.37 N*m (9 to 13 kgf*cm, 8 to 12 in.*lbf)

      If the preload is not as specified, replace the front differential case rear plate washer with one of a different thickness. Use the table below to select a front differential case rear plate washer which will ensure that the preload is within the specification.

      Standard Plate Washer Thickness
      Mark Specified Condition Mark Specified f0.417Condition
      10 2.100 mm (0.0827 in.) 26 2.500 mm (0.0984 in.)
      11 2.125 mm (0.0837 in.) 27 2.525 mm (0.0994 in.)
      12 2.150 mm (0.0846 in.) 28 2.550 mm (0.100 in.)
      13 2.175 mm (0.0856 in.) 29 2.575 mm (0.101 in.)
      14 2.200 mm (0.0866 in.) 30 2.600 mm (0.102 in.)
      15 2.225 mm (0.0876 in.) 31 2.625 mm (0.103 in.)
      16 2.250 mm (0.0886 in.) 32 2.650 mm (0.104 in.)
      17 2.275 mm (0.0896 in.) 33 2.675 mm (0.105 in.)
      18 2.300 mm (0.0906 in.) 34 2.700 mm (0.106 in.)
      19 2.325 mm (0.0915 in.) 35 2.725 mm (0.107 in.)
      20 2.350 mm (0.0925 in.) 36 2.750 mm (0.108 in.)
      21 2.375 mm (0.0935 in.) 37 2.775 mm (0.109 in.)
      22 2.400 mm (0.0945 in.) 38 2.800 mm (0.110 in.)
      23 2.425 mm (0.0955 in.) 39 2.825 mm (0.111 in.)
      24 2.450 mm (0.0965 in.) 40 2.850 mm (0.112 in.)
      25 2.475 mm (0.0974 in.) - -

      Tech Tips


      • Select a thicker plate washer to increase the preload, or a thinner plate washer to decrease the preload.

      • Make a memo as the torque values will be needed for the Adjust Output Shaft Bearing Preload procedure.

    5. Remove the 16 bolts and manual transmission case.

    6. Remove the differential case assembly from the front transaxle case.

    7. Replace the installed front differential case rear plate washer with the one selected above.

  4. INSTALL FRONT OUTPUT SHAFT BEARING


    1. B0040P7E04
      Text in Illustration
      *a Output Shaft Cover Key
      *b Case Groove

      Install the output shaft cover to the front transaxle case.

      Note

      Insert the output shaft cover key into the case groove.

    2. B0040NYE01

      Using SST and a press, install the front output shaft bearing (outer race) to the front transaxle case.

      SST
      09950-60010   ( 09951-00630 )
      09950-70010   ( 09951-07200 )

  5. INSTALL REAR OUTPUT SHAFT BEARING


    1. B0040HGE10
      Text in Illustration
      *1 Rear Output Shaft Bearing Shim

      Install the rear output shaft bearing shim to the manual transmission case.

    2. Using SST and a press, install the rear output shaft bearing (outer race) to the manual transmission case.

      SST
      09950-60010   ( 09951-00590 )
      09950-70010   ( 09951-07200 )

  6. ADJUST OUTPUT SHAFT BEARING PRELOAD


    1. B0040K3

      Coat the differential case assembly with gear oil and install it to the front transaxle case.

    2. B0040MW

      Coat the output shaft assembly with gear oil and install it to the front transaxle case.

    3. Install the manual transmission case with the 16 bolts.

      Torque:
      29 N*m  { 300 kgf*cm, 22 ft.*lbf }
    4. B0040PME04
      Text in Illustration
      *1 Bearing Shim

      Using SST and a torque wrench, turn the differential case assembly clockwise and counterclockwise 2 or 3 times to allow the bearings to settle.

      SST
      09564-32011

    5. Using SST and a torque wrench, measure the preload (value A). Calculate the rear output shaft bearing preload using the following formula.

      SST
      09564-32011
      Formula
      Value A - Differential side bearing preload = Output shaft bearing preload
      Standard Preload (at starting)
      Engine Item Specified Condition
      1ZR-FAE New bearing 4.54 to 7.98 N*m (47 to 81 kgf*cm, 41 to 70 in.*lbf)
      Used bearing 2.93 to 5.14 N*m (30 to 52 kgf*cm, 26 to 45 in.*lbf)
      2ZR-FAE New bearing 4.22 to 7.41 N*m (44 to 75 kgf*cm, 38 to 65 in.*lbf)
      Used bearing 2.72 to 4.77 N*m (28 to 48 kgf*cm, 25 to 42 in.*lbf)

      If the preload is not as specified, replace the rear output shaft bearing shim with one of a different thickness. Use the table below to select a rear output shaft bearing shim which will ensure that the preload is within the specification.

      Standard Bearing Shim Thickness
      Mark Specified Condition Mark Specified Condition
      50 1.750 mm (0.0689 in.) 72 2.300 mm (0.0906 in.)
      51 1.775 mm (0.0699 in.) 73 2.325 mm (0.0915 in.)
      52 1.800 mm (0.0709 in.) 74 2.350 mm (0.0925 in.)
      53 1.825 mm (0.0719 in.) 75 2.375 mm (0.0935 in.)
      54 1.850 mm (0.0728 in.) 76 2.400 mm (0.0945 in.)
      55 1.875 mm (0.0738 in.) 77 2.425 mm (0.0955 in.)
      56 1.900 mm (0.0748 in.) 78 2.450 mm (0.0965 in.)
      57 1.925 mm (0.0758 in.) 79 2.475 mm (0.0974 in.)
      58 1.950 mm (0.0768 in.) 80 2.500 mm (0.0984 in.)
      59 1.975 mm (0.0778 in.) 81 2.525 mm (0.0994 in.)
      60 2.000 mm (0.0787 in.) 82 2.550 mm (0.100 in.)
      61 2.025 mm (0.0797 in.) 83 2.575 mm (0.101 in.)
      62 2.050 mm (0.0807 in.) 84 2.600 mm (0.102 in.)
      63 2.075 mm (0.0817 in.) 85 2.625 mm (0.103 in.)
      64 2.100 mm (0.0827 in.) 86 2.650 mm (0.104 in.)
      65 2.125 mm (0.0837 in.) 87 2.675 mm (0.105 in.)
      66 2.150 mm (0.0846 in.) 88 2.700 mm (0.106 in.)
      67 2.175 mm (0.0856 in.) 89 2.725 mm (0.107 in.)
      68 2.200 mm (0.0866 in.) 90 2.750 mm (0.108 in.)
      69 2.225 mm (0.0876 in.) 91 2.775 mm (0.109 in.)
      70 2.250 mm (0.0886 in.) 92 2.800 mm (0.110 in.)
      71 2.275 mm (0.0896 in.) - -

      Tech Tips

      Select a thicker bearing shim to increase the preload, or a thinner bearing shim to decrease the preload.

    6. Remove the 16 bolts and manual transmission case.

    7. Remove the output shaft assembly from the front transaxle case.

    8. Remove the differential case assembly from the front transaxle case.

    9. Replace the installed rear output shaft bearing shim with the one selected above.

  7. INSTALL OUTER SHIFT LEVER OIL SEAL


    1. B0040L0E12
      Text in Illustration
      *a Depth

      Using SST and a hammer, install a new outer shift lever oil seal to the manual transmission case.

      SST
      09950-60010   ( 09951-00260 )
      09950-70010   ( 09951-07100 )
      Standard depth
      0.5 to 1.0 mm (0.0197 to 0.0393 in.)

    2. Coat the lip of the outer shaft lever oil seal with MP grease.

  8. INSTALL OUTER NO. 1 SHIFT LEVER


    1. B0040NEE04
      Text in Illustration
      *a Mark
      *b Depth

      Install the inner No. 1 shift lever, outer shift lever spacer and outer No. 1 shift lever to the manual transmission case.

      Tech Tips

      Install the inner No. 1 shift lever with its mark facing outside of the manual transmission case.

    2. Using a 5 mm pin punch and hammer, install the inner shift lever slotted spring pin to the inner No. 1 shift lever.

      Standard depth
      -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

  9. INSTALL MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY


    1. B0040M5

      Install the manual transmission oil separator sub-assembly to the manual transmission case with the 4 bolts.

      Torque:
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }

      Tech Tips

      Make sure that the end tabs of the manual transmission oil separator sub-assembly are inserted in the grooves of the manual transmission case.

  10. INSTALL TRANSMISSION OIL SEPARATOR


    1. B0040Q2

      For manual transmission case side:

      Install the transmission oil separator to the manual transmission case with the 2 bolts.

      Torque:
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }

      Tech Tips

      Make sure that the tip of the transmission oil separator is inserted in the groove of the transmission case.

  11. INSTALL NO. 1 OIL RECEIVER PIPE


    1. B0040NN

      Install the No. 1 oil receiver pipe to the manual transmission case.

      Tech Tips

      Make sure that the No. 1 oil receiver pipe fully contacts the manual transmission case.

  12. INSTALL STRAIGHT PIN


    1. B0040KVE06
      Text in Illustration
      *a Protrution

      Using a plastic-faced hammer, tap in 5 new straight pins to the specified protrusion height.

      Protrusion height
      8.5 to 9.5 mm (0.335 to 0.374 in.)

  13. INSTALL REVERSE RESTRICT PIN ASSEMBLY

    w/ Reverse Restrict Pin Assembly:


    1. B0040QB

      Install the reverse restrict pin assembly to the front transaxle case.

  14. INSTALL BREATHER PLUG


    1. B0040MAE03

      Using SST and a hammer, install the breather plug to the front transaxle case.

      SST
      09350-30020   ( 09350-07110 )

  15. INSTALL TRANSMISSION OIL SEPARATOR


    1. B0040HC

      For front transaxle case side:

      Install the transmission oil separator to the front transaxle case with the 4 bolts.

      Torque:
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }

  16. INSTALL FRONT TRANSAXLE CASE OIL SEAL


    1. B0040I8E06
      Text in Illustration
      *a Depth

      Using SST and a hammer, install a new front transaxle case oil seal to the front transaxle case.

      SST
      09950-60010   ( 09951-00350 )
      09950-70010   ( 09951-07100 )
      Standard depth
      0.9 to 1.9 mm (0.0354 to 0.0748 in.)

    2. Coat the lip of the front transaxle case oil seal with MP grease.

  17. INSTALL TRANSMISSION MAGNET


    1. B0040FT

      Clean the transmission magnet and install it to the front transaxle case.

  18. INSTALL INPUT SHAFT COVER


    1. B0040K9E03
      Text in Illustration
      *a Input Shaft Cover Key
      *b Case Groove

      Install the input shaft cover to the manual transmission case.

      Note

      Insert the input shaft cover key into the manual transmission case groove.

  19. INSTALL REAR INPUT SHAFT BEARING SHIM


    1. Install the rear input shaft bearing shim to the manual transmission case.

      Note

      Apply grease to the shim to prevent it from falling off of the case during assembly.

    2. Measure the distance between the end of the manual transmission case and rear input shaft bearing shim (Dimension A).

      B0040G2E01

    3. Measure the distance between the end of the front transaxle case and installation surface of the front input shaft bearing (Dimension B).

      Text in Illustration
      *1 Manual Transmission Case
      *2 Input Shaft Assembly
      *3 Front Transaxle Case
      *4 Dimension A
      *5 Dimension B
      *6 Dimension C

    4. Measure the distance between both input shaft bearing outer races (Dimension C).

      Note

      Measure Dimension C with each bearing having no axial clearance.

    5. Calculate the rear input shaft bearing shim clearance using the following formula.

      Formula
      (Dimension A + Dimension B) - Dimension C - Rear input shaft bearing shim thickness = Between 0.02 mm (0.000788 in.) and 0.14 mm (0.00551 in.)

      If the clearance is not as specified, replace the rear input shaft bearing shim with one of a different thickness. Use the table below to select a rear input shaft bearing shim which will ensure that the clearance is within the specification.

      Standard Rear Input Shaft Bearing Shim Thickness
      Mark Specified Condition Mark Specified Condition
      08 1.30 mm (0.0512 in.) 14 1.60 mm (0.0630 in.)
      09 1.35 mm (0.0531 in.) 15 1.65 mm (0.0650 in.)
      10 1.40 mm (0.0551 in.) 16 1.70 mm (0.0669 in.)
      11 1.45 mm (0.0571 in.) 17 1.75 mm (0.0689 in.)
      12 1.50 mm (0.0591 in.) 18 1.80 mm (0.0709 in.)
      13 1.55 mm (0.0610 in.) 19 1.85 mm (0.0728 in.)

    6. Coat the selected rear input shaft bearing shim with MP grease, and then replace the installed rear input shaft bearing shim with the one selected above.

      Note

      Do not apply MP grease to the oil grooves.

  20. INSTALL DIFFERENTIAL CASE ASSEMBLY


    1. B0040K3

      Coat the differential case tapered roller bearing with gear oil and install it to the front transaxle case.

  21. INSTALL INPUT SHAFT ASSEMBLY


    1. Apply gear oil to all sliding and rotating parts.

    2. B0040L5E02
      Text in Illustration
      *1 No. 1 Gear Shift Fork Shaft Assembly
      *2 Output Shaft Assembly

      Coat the No. 1 gear shift fork shaft assembly with gear oil and install it.

    3. B0040IBE06
      Text in Illustration
      *1 No. 2 Gear Shift Fork Shaft Assembly
      *2 No. 3 Gear Shift Fork Shaft Assembly
      *3 Input Shaft Assembly

      Coat the No. 2 gear shift fork shaft assembly and No. 3 gear shift fork shaft assembly with gear oil and install them.

    4. Temporarily install the output shaft with No. 1 gear shift fork shaft to the input shaft assembly, and tie them with a rope or string.

    5. B0040HV

      Install the input shaft assembly, output shaft assembly and 3 gear shift fork shaft assemblies to the front transaxle case.

  22. INSTALL OUTER SELECT LEVER OIL SEAL


    1. B0040KHE02
      Text in Illustration
      *a Depth

      Using SST and a hammer, install a new outer select lever oil seal to the front transaxle case.

      SST
      09950-60010   ( 09951-00240 )
      09950-70010   ( 09951-07100 )
      Standard depth
      0.5 to 1.0 mm (0.0197 to 0.0393 in.)

    2. Coat the lip of the outer select lever oil seal with MP grease.

  23. INSTALL OUTER SELECT LEVER


    1. B0040NWE17
      Text in Illustration
      *a Mark

      Install the inner select lever and outer select lever to the front transaxle case.

      Tech Tips

      Install the inner select lever with its mark facing outside of the front transaxle case.

  24. INSTALL SHIFT AND SELECT LEVER SHAFT ASSEMBLY


    1. B0040MQE02
      Text in Illustration
      *1 Shift and Select Lever Shaft Assembly
      *2 Inner Select Lever
      *3 Shift Inner Lock Plate

      Install the shift interlock plate and shift and select lever shaft assembly to the front transaxle case, and then turn them counterclockwise.

      Tech Tips

      When installing the inner select lever, make sure to engage it with the shift inner lock plate.

    2. B0040M8

      Coat the threads of the inner select lever set bolt with sealant and install it using a 6 mm hexagon socket wrench.

      Sealant
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
      Torque:
      28 N*m  { 286 kgf*cm, 21 ft.*lbf }

  25. INSTALL REVERSE SHIFT ARM BRACKET ASSEMBLY


    1. B0040MR

      Install the reverse shift arm bracket assembly to the front transaxle case with the 2 bolts.

      Torque:
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }

  26. INSTALL REVERSE SHIFT FORK SHAFT ASSEMBLY


    1. B0040GK

      Coat the reverse shift fork shaft assembly with gear oil and install it to the front transaxle case.

  27. INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY


    1. B0040KWE06
      Text in Illustration
      *a Parallel
      *b Reverse Idler Gear Shaft Bolt Installation Surface
      *c Screw Hole

      Coat the reverse idler gear sub-assembly, thrust washer and reverse idler gear shaft with gear oil, and install them as shown in the illustration.

      Note

      Be sure to align the bolt hole of the reverse idler gear shaft with the bolt hole of the front transaxle case. Make sure that the axis of the reverse idler gear shaft bolt hole is parallel to the line from the center of the top of the input shaft to the other bolt hole of the front transaxle case, as shown in the illustration.

      Tech Tips

      Raise the edge of the reverse shift arm bracket assembly and connect the reverse shift arm bracket assembly to the reverse shift fork shaft assembly.

  28. INSTALL MANUAL TRANSMISSION CASE


    1. B0040OLE07
      Text in Illustration
      *a Seal Packing

      Apply seal packing to the manual transmission case as shown in the illustration.

      Parallel

      Seal packing
      Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
      Standard seal diameter
      1.2 mm (0.0472 in.)

      Note


      • Remove any oil from the contact surfaces.

      • Assemble the parts within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.

    2. B0040OF

      Push the outer No. 1 shift lever and install the manual transmission case.

      Tech Tips

      Pushing the outer No. 1 shift lever allows the manual transmission case to be installed.

    3. B0040L2

      Turn the outer No. 1 shift lever counterclockwise and then pull it.

    4. B0040MT

      Install the 16 bolts to the manual transmission case.

      Torque:
      29 N*m  { 300 kgf*cm, 22 ft.*lbf }

  29. INSTALL OUTER SHIFT LEVER E RING


    1. B0040HF

      Install the E ring to the outer No. 1 shift lever.

  30. INSTALL FRONT DRIVE SHAFT OIL SEAL LH

    Click here

  31. INSTALL FRONT DRIVE SHAFT OIL SEAL RH

    Click here

  32. INSTALL SHIFT DETENT BALL


    1. B0040L4

      Install the 2 shift detent balls and 2 compression springs to the manual transmission case.

      Note

      Be careful not to drop the ball into the manual transmission case.

    2. Coat the threads of the 2 shift detent ball plugs with sealant and install them using a 6 mm hexagon socket wrench.

      Sealant
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
      Torque:
      22 N*m  { 224 kgf*cm, 16 ft.*lbf }
    3. B0040M2

      Install the shift detent ball and compression spring to the manual transmission case.

      Note

      Be careful not to drop the ball into the manual transmission case.

    4. Coat the threads of the shift detent ball plug with sealant and install it using a 6 mm hexagon socket wrench.

      Sealant
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
      Torque:
      22 N*m  { 224 kgf*cm, 16 ft.*lbf }

  33. INSTALL LOCK BALL PIN


    1. B0040O2

      Install the lock ball pin and compression spring to the manual transmission case.

      Note

      Be careful not to drop the lock ball pin into the manual transmission case.

    2. Coat the threads of the shift detent ball plug with sealant and install it using a 10 mm hexagon socket wrench.

      Sealant
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
      Torque:
      25 N*m  { 250 kgf*cm, 18 ft.*lbf }

  34. INSTALL REVERSE IDLER GEAR SHAFT BOLT


    1. B0040GN

      Install a new gasket and the reverse idler gear shaft bolt to the manual transmission case.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }

  35. INSTALL NO. 1 LOCK BALL ASSEMBLY


    1. B0040QF

      Coat the threads of the No. 1 lock ball assembly with sealant and install it to the manual transmission case.

      Sealant
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
      Torque:
      29 N*m  { 300 kgf*cm, 22 ft.*lbf }

  36. INSTALL TRANSMISSION CASE PLUG


    1. B0040HO

      Install a new gasket and the transmission case plug to the manual transmission case.

      Torque:
      28 N*m  { 286 kgf*cm, 21 ft.*lbf }

  37. INSTALL NO. 1 CLUTCH HOUSING COVER


    1. B0040NB

      Install the No. 1 clutch housing cover to the front transaxle case.

  38. INSTALL RELEASE CYLINDER BLEEDER PLUG


    1. Install the release cylinder bleeder plug to the clutch release bleeder sub-assembly.

      Torque:
      8.4 N*m  { 86 kgf*cm, 74 in.*lbf }

  39. INSTALL RELEASE CYLINDER BLEEDER PLUG CAP


    1. Install the release cylinder bleeder plug cap onto the release cylinder bleeder plug.

  40. INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY

    Click here

  41. INSPECT CLUTCH PIPE LINE

    Click here

  42. INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

    Click here

  43. INSTALL WIRE HARNESS CLAMP BRACKET


    1. B0040GZ

      Install the wire harness clamp bracket to the manual transmission case with the bolt.

      Torque:
      13 N*m  { 132 kgf*cm, 10 ft.*lbf }

  44. INSTALL CONTROL CABLE BRACKET ASSEMBLY


    1. B0040OEE01
      Text in Illustration
      *1 Reverse Restrict Pin Assembly
      *2 Outer Lever

      w/ Reverse Restrict Pin Assembly:

      Hook the outer lever of the manual transaxle onto the reverse restrict pin assembly to secure it.

    2. B0040KLE02
      Text in Illustration
      *1 Outer Lever
      *a Installation hole for transmission control select cable adjustment
      *b Cutout

      w/o Reverse Restrict Pin Assembly:

      Align the outer lever cutout with the hole for adjusting the transmission control select cable, and insert the bolt by hand to secure the outer lever as shown in the illustration.

      Note


      • In order to avoid case damage, do not push the bolt in forcefully.

      • After adjusting the transmission control select cable, pull out the bolt.

      Tech Tips


      • Use a bolt with a diameter of 6.0 mm (0.236 in.) and a length of at least 18 mm (0.709 in.) or more.

      • Depending on the actual bolt diameter, it may be difficult to insert the bolt. In that case, as there is some variation in actual bolt diameters, use a 6.0 mm (0.236 in.) bolt with a comparatively small diameter.

    3. B0040MX

      Install the control cable bracket assembly to the manual transmission case with the 3 bolts.

      Torque:
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }

  45. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    1. B0040N8

      Using a 27 mm deep socket wrench, install a new gasket and the neutral position switch to the manual transmission case.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

  46. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY


    1. B0040MK

      Using a 27 mm deep socket wrench, install a new gasket and the back-up light switch to the manual transmission case.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

  47. INSTALL MANUAL TRANSMISSION FILLER PLUG


    1. B0040Q8

      Install a new gasket and the manual transmission filler plug to the manual transmission case.

      Torque:
      39 N*m  { 400 kgf*cm, 29 ft.*lbf }

      Tech Tips

      Face the tapered side of the gasket toward the manual transmission case.

  48. INSTALL MANUAL TRANSMISSION DRAIN PLUG


    1. B0040F6

      Using a 10 mm hexagon socket wrench, install a new gasket and the manual transmission drain plug to the front transaxle case.

      Torque:
      45 N*m  { 459 kgf*cm, 33 ft.*lbf }

      Tech Tips

      Face the tapered side of the gasket toward the front transaxle case.