DATA LIST
Tech Tips
Using the GTS to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Cruise Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| CCS Vehicle Spd | Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph) | Actual vehicle speed displayed | - |
| CCS Mem Vehicle Spd | Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph) | Vehicle speed stored in memory | - |
| Throttle Opening Angle | Required throttle opening angle / Min.: 0 deg, Max.: 124.4 deg | Actual required throttle opening amount | - |
| Cruise Operation Status | Shift lever position signal / ON or OFF | ON: Shift lever in D OFF: Shift lever not in D |
- |
| Cruise Control | Cruise control / ON or OFF | ON: Cruise control set OFF: Cruise control not set |
- |
| CCS Indicator M-CPU | CRUISE main indicator (Main CPU) / ON or OFF | ON: CRUISE main indicator light on OFF: CRUISE main indicator light off |
- |
| CCS Indicator S-CPU | CRUISE main indicator (Sub CPU) / ON or OFF | ON: CRUISE main indicator light on OFF: CRUISE main indicator light off |
- |
| CCS Ready S-CPU | Cruise control system standby condition (Sub CPU) / ON or OFF | ON: Cruise control switch on OFF: Cruise control switch off |
- |
| CCS Ready M-CPU | Cruise control system standby condition (Main CPU) / ON or OFF | ON: Cruise control switch on OFF: Cruise control switch off |
- |
| Main SW S-CPU | Cruise control switch (Sub CPU) / ON or OFF | ON: Cruise control switch on OFF: Cruise control switch off |
- |
| Main SW M-CPU | Cruise control switch (Main CPU) / ON or OFF | ON: Cruise control switch on OFF: Cruise control switch off |
- |
| Cancel Switch | CANCEL switch signal / ON or OFF | ON: CANCEL switch on OFF: CANCEL switch off |
- |
| SET/COAST Switch | -SET switch signal / ON or OFF | ON: -SET switch on OFF: -SET switch off |
- |
| RES/ACC Switch | +RES switch signal / ON or OFF | ON: +RES switch on OFF: +RES switch off |
- |
| Stp Light SW M-CPU | Stop light switch signal (Main CPU) / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released |
- |
| Stp Light SW S2-CPU | Stop light switch signal (Sub CPU) / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released |
- |
| Stp Light SW S1-CPU | Stop light switch signal (Sub CPU) / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released |
- |
| Cruise Request Driving Force* | Cruise control driving force signal / Min.: -51.2 kN, Max.: 51.2 kN | Actual driving force | - |
*: for CVT
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Indicat. Lamp Cruise | Cruise control indicator light | ON/OFF | - |
| Indicat. SET | Cruise control SET indicator light | ON/OFF | - |