CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM, Diagnostic DTC:P0717, P07BF, P07C0

DTC Code DTC Name
P0717 Input/Turbine Speed Sensor "A" Circuit No Signal
P07BF Input/Turbine Speed Sensor "A" Circuit Low
P07C0 Input/Turbine Speed Sensor "A" Circuit High

DESCRIPTION

The ECM receives a signal from the transmission revolution sensor (NT) installed in the continuously variable transaxle to control the lock-up engagement pressure and forward and reverse clutch pressure.

The transmission revolution sensor (NT) detects the continuously variable transaxle input shaft speed and sends a signal to the ECM.

DTC No.

DTC Detection Condition


  1. Diagnosis Condition

  2. Malfunction Status

  3. Malfunction Time

  4. Other

 Trouble Area
P0717

  1. The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more, and no error is detected in the park/neutral position switch assembly.

  2. The speed indicated by the transmission revolution sensor (NT) is less than 300 rpm.

  3. 2 seconds

  4. 1-trip detection logic

  • Harness or connector

  • Transmission revolution sensor (NT)

  • ECM
P07BF

  1. A transmission revolution sensor (NT) signal malfunction is not detected.

  2. The transmission revolution sensor (NT) output voltage is below 0.1 V.

  3. 2 seconds

  4. 1-trip detection logic

  • Harness or connector

  • Transmission revolution sensor (NT)

  • ECM
P07C0

  1. A transmission revolution sensor (NT) signal malfunction is not detected.

  2. The transmission revolution sensor (NT) output voltage is higher than 1.9 V.

  3. 2 seconds

  4. 1-trip detection logic

  • Harness or connector

  • Transmission revolution sensor (NT)

  • ECM

MONITOR DESCRIPTION

The transmission revolution sensor (NT) detects the transaxle input shaft speed. The ECM determines the necessary gear ratio based on a comparison of the transmission revolution sensor (NT) (input shaft speed) with the transmission revolution sensor (NOUT) (output shaft speed).

When the output shaft speed is higher than the expected value and the input shaft speed is less than 300 rpm while driving with the shift lever in D, the ECM will determine that the transmission revolution sensor (NT) is malfunctioning. The ECM will illuminate the MIL and store a DTC.

WIRING DIAGRAM

A00550SE12
*a Transmission Revolution Sensor (NT)

CAUTION / NOTICE / HINT

Note


  • Perform initialization when parts related to the continuously variable transaxle are replaced Click here.

  • Check that no DTCs are stored after performing initialization Click here.

PROCEDURE


  1. READ VALUE USING GTS (SPD (NT) AND NT SENSOR VOLTAGE)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.

    5. In accordance with the display on the GTS, read the Data List.

      Engine and ECT
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      SPD (NT)

      Input turbine speed/

      Min.: 0 rpm

      Max.: 12750 rpm

      • Input turbine speed (NT) equal to engine speed (NE): Lock-up ON (After warming up engine)

      • Input turbine speed (NT) nearly equal to engine speed (NE): Lock-up OFF (Idling with shift lever in P or N)

      • 0 rpm: Vehicle stopped with shift lever in D or R

      		 Data is displayed in increments of 50 rpm.
      NT Sensor Voltage

      Input turbine speed (NT) sensor output voltage/

      Min.: 0.000 V

      Max.: 4.999 V

      		 0.1 to 1.9 V: Engine idling (Vehicle stopped with shift lever in P or N) -
      Result
      Result Proceed to
      Data display is not within Normal Condition range A
      Data display is within Normal Condition range B

    B

    REPLACE ECM Click here

    A

  2. INSPECT TRANSMISSION REVOLUTION SENSOR (NT)


    1. Remove the transmission revolution sensor (NT) Click here.

    2. Connect the battery to the sensor as shown in the illustration.

      A0056NRE04
      Text in Illustration
      *1 Battery *2 Ammeter
      *a

      Component without harness connected

      (Transmission Revolution Sensor (NT))

      		 *b Magnet
      *c 5 mm or less - -

    3. Wave a magnetic object left and right in front of the transmission revolution sensor (NT) tip (5 mm (0.197 in.) or less) to change the high/low signals while measuring the current.

      Note

      Make sure to wave the magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.

    4. Measure the current according to the value(s) in the table below.

      Standard Current
      Tester Connection Condition Specified Condition
      1 (NTO) - 2 (NTB) Low signal 4 to 8 mA
      1 (NTO) - 2 (NTB) High signal 12 to 16 mA

    NG

    REPLACE TRANSMISSION REVOLUTION SENSOR (NT) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTIONSENSOR (NT) - ECM)


    1. Disconnect the B35 transmission revolution sensor (NT) connector.

    2. Disconnect the B53 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B35-1 (NTO) - B53-125 (NTO) Always Below 1 Ω
      B35-2 (NTB) - B53-126 (NTB) Always Below 1 Ω
      B35-1 (NTO) or B53-125 (NTO) - Body ground and other terminals Always 10 kΩ or higher
      B35-2 (NTB) or B53-126 (NTB) - Body ground and other terminals Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - ECM)

    OK

  4. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

    PERFORM INITIALIZATION Click here

  5. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

    PERFORM INITIALIZATION Click here