OUTER MIRROR SWITCH INSPECTION


  1. INSPECT OUTER MIRROR SWITCH ASSEMBLY


    1. w/o Retract mirror


      1. Check the mirror select switch and mirror surface adjust switch.

      2. A01HT3TE05
        Text in Illustration
        *1 Mirror select switch
        *2 Mirror surface adjust switch
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Turn the mirror select switch to the L position.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for left side)
        Tester Connection Switch Condition Specified Condition

        9 (MLV) - 13 (B)

        11 (M+) - 12 (E)

        		 UP Below 1 Ω
        OFF 10 kΩ or higher

        9 (MLV) - 12 (E)

        11 (M+) - 13 (B)

        		 DOWN Below 1 Ω
        OFF 10 kΩ or higher

        10 (MLH) - 13 (B)

        11 (M+) - 12 (E)

        		 LEFT Below 1 Ω
        OFF 10 kΩ or higher

        10 (MLH) - 12 (E)

        11 (M+) - 13 (B)

        		 RIGHT Below 1 Ω
        OFF 10 kΩ or higher

      4. Turn the mirror select switch to the R position.

      5. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)
        Tester Connection Switch Condition Specified Condition

        8 (MRV) - 13 (B)

        11 (M+) - 12 (E)

        		 UP Below 1 Ω
        OFF 10 kΩ or higher

        8 (MRV) - 12 (E)

        11 (M+) - 13 (B)

        		 DOWN Below 1 Ω
        OFF 10 kΩ or higher

        7 (MRH) - 13 (B)

        11 (M+) - 12 (E)

        		 LEFT Below 1 Ω
        OFF 10 kΩ or higher

        7 (MRH) - 12 (E)

        11 (M+) - 13 (B)

        		 RIGHT Below 1 Ω
        OFF 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    2. Check the LED illuminates (w/o Retract mirror).


      1. A01HT3TE03
        Text in Illustration
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        Standard
        Measurement Condition Specified Condition

        Auxiliary battery positive (+) → Terminal 6 (ILL+)

        Auxiliary battery negative (-) → Terminal 16 (ILL-)

        		 LED illuminates

        If the result is not as specified, replace the outer mirror switch assembly.

    3. w/ Retract mirror


      1. Check the mirror select switch and mirror surface adjust switch.

      2. A01HTZPE12
        Text in Illustration
        *1 Mirror select switch
        *2 Mirror surface adjust switch
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Turn the mirror select switch to the L position.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for left side)
        Tester Connection Switch Condition Specified Condition

        9 (MLV) - 13 (B)

        11 (M+) - 12 (E)

        		 UP Below 1 Ω
        OFF 10 kΩ or higher

        9 (MLV) - 12 (E)

        11 (M+) - 13 (B)

        		 DOWN Below 1 Ω
        OFF 10 kΩ or higher

        10 (MLH) - 13 (B)

        11 (M+) - 12 (E)

        		 LEFT Below 1 Ω
        OFF 10 kΩ or higher

        10 (MLH) - 12 (E)

        11 (M+) - 13 (B)

        		 RIGHT Below 1 Ω
        OFF 10 kΩ or higher

      4. Turn the mirror select switch to the R position.

      5. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)
        Tester Connection Switch Condition Specified Condition

        8 (MRV) - 13 (B)

        11 (M+) - 12 (E)

        		 UP Below 1 Ω
        OFF 10 kΩ or higher

        8 (MRV) - 12 (E)

        11 (M+) - 13 (B)

        		 DOWN Below 1 Ω
        OFF 10 kΩ or higher

        7 (MRH) - 13 (B)

        11 (M+) - 12 (E)

        		 LEFT Below 1 Ω
        OFF 10 kΩ or higher

        7 (MRH) - 12 (E)

        11 (M+) - 13 (B)

        		 RIGHT Below 1 Ω
        OFF 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    4. Check the mirror retract switch (w/ Retract mirror).


      1. A01HTZPE13
        Text in Illustration
        *1 Mirror retract switch
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        15 (MF) - 12 (E) Mirror retract switch retract position Below 1 Ω
        14 (MR) - 13 (B) Below 1 Ω
        15 (MF) - 13 (B) Mirror retract switch return position Below 1 Ω
        14 (MR) - 12 (E) Below 1 Ω

        If the result is not as specified, replace the outer mirror switch assembly.

    5. Check the LED illuminates (w/ Retract mirror).


      1. A01HTZPE14
        Text in Illustration
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        Standard
        Measurement Condition Specified Condition

        Auxiliary battery positive (+) → Terminal 6 (ILL+)

        Auxiliary battery negative (-) → Terminal 16 (ILL-)

        		 LED illuminates

        If the result is not as specified, replace the outer mirror switch assembly.