LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY REMOVAL


  1. REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)

    Click here

  2. REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)

    Click here

  3. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.


      1. A01HU3FE01

        Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

        Standard Measurement
        a 100 mm (3.94 in.) or less

      2. Repeat the step above for the other hook.

    2. Remove the rear seat cushion assembly.

  4. REMOVE REAR SEAT CUSHION LOCK HOOK


    1. A01HVMY

      Disengage the claw and remove the rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  5. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide LH.

    2. Disconnect the connector.

    3. A01HT1N

      Remove the 2 bolts.

    4. Disengage the hook and remove the rear side seatback assembly LH.

  6. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01HTTW

      Disengage the 10 claws and remove the front door scuff plate LH.

  7. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Disconnect the front door opening trim weatherstrip.

  8. REMOVE REAR DOOR SCUFF PLATE LH


    1. A01HV33

      Disengage the 6 claws and remove the rear door scuff plate LH.

      Tech Tips

      Disengage the claws from the rear side of the scuff plate.

  9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Disconnect the rear door opening trim weatherstrip.

  10. REMOVE LAP BELT OUTER ANCHOR COVER


    1. A01HUG1

      Disengage the 3 claws and remove the lap belt outer anchor cover.

  11. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A01HVXN

      Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.

  12. REMOVE CENTER PILLAR LOWER GARNISH LH


    1. A01HT7E

      Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.

  13. REMOVE LUGGAGE COMPARTMENT DOOR COVER


    1. A01HVNE

      Remove the 13 clips and luggage compartment door cover.

  14. REMOVE SPARE WHEEL COVER ASSEMBLY


    1. Remove the spare wheel cover assembly.

  15. REMOVE REAR FLOOR FINISH PLATE


    1. A01HUSM

      Remove the 5 clips.

    2. A01HU2Q

      Disengage the 4 clips and remove the rear floor finish plate.

  16. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. A01HTPXE01
      Text in Illustration
      *1 Pin

      Push the pin and remove the No. 1 luggage compartment trim hook.

  17. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH


    1. A01HW3NE01
      Text in Illustration
      *1 Clip <A>
      *2 Clip <B>

      Remove the clip <A>.

    2. Remove the 2 clips <B>.

    3. Disengage the fastener and remove the luggage compartment inner trim cover LH.

  18. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    1. A01HV4B

      Remove the screw.

    2. A01HW22

      Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.

    3. A01HVU2

      Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.

  19. REMOVE LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY


    1. A01HV11

      Disengage the 2 clamps.

    2. A01HVIY

      Using a clip remover, disengage the clamp and disconnect the wire harness.

    3. A01HTJA

      Using a clip remover, disengage the 2 clamps and remove the 2 scuff plate clips.

    4. Turn back the floor carpet so that the luggage door lock control cable sub-assembly and fuel lid lock control cable sub-assembly can be removed.

    5. A01HUS5

      Disengage the guide as shown in the illustration.

    6. A01HUAE

      Disconnect the luggage door lock control cable sub-assembly.

    7. A01HVPA

      Disengage the clamp and disconnect the luggage door lock control cable sub-assembly.

    8. A01HT6ME01
      Text in Illustration
      *1 Cutout
      *2 Guide <A>

      Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides <A>, and then pull the fuel filler opening lid lock retainer.

    9. A01HTJQE01
      Text in Illustration
      *1 Cutout
      *2 Guide <B>

      Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and guides <B>, and then pull the fuel filler opening lid lock retainer.

    10. A01HUMGE01
      Text in Illustration
      *1 Cutout
      *2 Guide <C>
      *3 Guide <B>

      Pull out the fuel filler opening lid lock retainer with both guides <B> and <C> aligned with the cutouts.

    11. A01HTSB

      Disengage the 2 claws and remove the fuel filler opening lid lock retainer.

    12. Disengage the 10 clamps and remove the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

      A01HV25E01
      Text in Illustration
      *1 Fuel Lid Lock Control Cable Sub-assembly *2 Luggage Door Lock Control Cable Sub-assembly

    13. Using a knife, cut off the clamp as shown in the illustration.

      A01HT7IE01
      Text in Illustration
      *1 Tape - -
      *a Cut - -

      Note

      Be careful not to damage the vehicle fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

    14. Remove the clamp.

    15. Remove the 3 pieces of tape and fuel lid lock control cable sub-assembly.