POWER WINDOW REGULATOR MOTOR (for Rear Door) REMOVAL

Tech Tips


  • Use the same procedure for both the RH and LH sides.

  • The procedure described below is for the LH side.


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER


    1. A01HUM2

      Disengage the claw to remove the luggage trim service hole cover.

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A01HW25

      Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.

  5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A01HW09

      Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  6. REMOVE REAR ARMREST ASSEMBLY


    1. A01HV1M

      Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.

  7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01HVH2E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the rear door panel.

    2. A01HSHP

      Remove the 3 screws.

    3. Using a clip remover, disengage the 8 clips.

    4. A01HVEWE01
      Text in Illustration
      *1 Reference Boss
      *2 Rear Door Inner Glass Weatherstrip

      Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    5. Disengage the reference boss from the rear door panel.

    6. Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

    7. A01HSCN

      Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

    8. A01HTV6E01
      Text in Illustration
      *1 Screwdriver

      Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.

  8. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    1. A01HTBDE01
      Text in Illustration
      *1 Screwdriver

      Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.

  9. REMOVE REAR DOOR SERVICE HOLE COVER


    1. A01HU90

      Disconnect the connector and remove the rear door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  10. DISCONNECT REAR DOOR WEATHERSTRIP


    1. A01HTMD

      Disconnect the upper part of rear door weatherstrip as shown in the illustration.

  11. REMOVE REAR DOOR GLASS RUN


    1. A01HVCW

      Remove the rear door glass run.

  12. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    1. A01HSYH

      Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.

      Note

      When the rear door lower window frame sub-assembly is removed, do not allow the rear door quarter window glass to fall.

  13. REMOVE REAR DOOR QUARTER WINDOW GLASS


    1. A01HVRV

      Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.

  14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. A01HTR7

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  15. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY


    1. A01HTWUE01
      Text in Illustration
      *1 Temporary Bolt

      Disconnect the connector.

    2. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator assembly may fall and cause damage.

    3. Remove the 3 bolts.

    4. Remove the rear door window regulator assembly.

    5. Remove the temporary bolt from the rear door window regulator assembly.

  16. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY


    1. A01HSA4

      Using a T25 "TORX" socket wrench, remove the 3 screws and rear power window regulator motor assembly.