POWER WINDOW REGULATOR MOTOR (for Front Door) REMOVAL

Tech Tips


  • Use the same procedure for both the RH and LH sides.

  • The procedure described below is for the LH side.


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER


    1. A01HUM2

      Disengage the claw to remove the luggage trim service hole cover.

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01HT07

      Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.

  5. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. A01HT5B

      Disengage the 3 clips and remove the front door lower frame bracket garnish.

  6. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A01HW1C

      Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

    2. Disconnect each connector and remove the power window regulator master switch assembly with front door armrest base panel.

  7. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A01HVRO

      Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

    2. Disconnect each connector and remove the power window regulator switch assembly with front door armrest base panel.

  8. REMOVE FRONT ARMREST ASSEMBLY


    1. A01HSTH

      Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the front armrest assembly.

  9. REMOVE COURTESY LIGHT ASSEMBLY


    1. A01HV6FE01
      Text in Illustration
      *A for LH Side
      *B for RH Side
      *1 Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01HVVFE01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the front door panel.

    2. A01HVLJ

      Remove the 3 screws.

    3. Using a clip remover, disengage the 10 clips.

    4. A01HVDSE01
      Text in Illustration
      *1 Reference Boss
      *2 Front Door Inner Glass Weatherstrip

      Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    5. Disengage the reference boss from the front door panel.

    6. Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.

    7. A01HVYG

      Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.

  11. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    1. A01HTJEE01
      Text in Illustration
      *1 Screwdriver

      Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.

  12. REMOVE DOOR SIDE AIRBAG SENSOR


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Disconnect the connector from the door side airbag sensor.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

        A01HV1HE12
        Text in Illustration
        *1 White Housing Lock *2 Yellow CPA
        *a Connector Lock is Released - -

      2. Push down the white housing lock again and disconnect the connector.

        Note

        Do not push down the part (A) shown in the illustration when disconnecting the connector.

    4. A01HUYE

      Remove the bolt and door side airbag sensor from the front door panel.

      Note

      Loosen the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.

    5. After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

      A01HSORE01
      Text in Illustration
      *a Incorrect *b Correct

  13. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. A01HSIG

      Remove the bolt.

    2. Disconnect each connector.

    3. Disengage the 5 clamps.

    4. Remove the front door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. A01HTT3

      Remove the grommet.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    4. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    5. Disconnect the power window regulator master switch assembly.

    6. A01HVFI

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door glass to fall.

    7. A01HTLYE01

      Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

      Note

      Do not damage the door glass.

  15. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY


    1. A01HTDEE01
      Text in Illustration
      *1 Temporary Bolt

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.

    2. Remove the 5 bolts.

    3. Remove the front door window regulator assembly.

    4. Remove the temporary bolt from the front door window regulator assembly.

  16. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY


    1. A01HVYU

      Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly.