ROOF HEADLINING INSTALLATION


  1. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)


    1. A01HVM4E01
      Text in Illustration
      *1 Clip (Black)
      *2 Clip (White)

      Install the 2 clips to the roof headlining assembly.

    2. A01HSBS

      Put the roof headlining assembly into the vehicle through the front door RH.

      Note

      Do not damage the roof headlining assembly or body interior.

    3. Engage the 2 clips.

      A01HTXRE01
      Text in Illustration
      *A w/o Satellite Radio *B w/ Satellite Radio

    4. Install the roof headlining assembly with the 2 clips.

    5. Engage the 4 clamps to the front pillar LH.

    6. Engage the 3 clamps to the front pillar RH.

    7. Connect the bracket with the bolt to the front pillar RH.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    8. w/o Satellite Radio:


      1. Engage the 2 clamps and connect the connector to the rear pillar RH.

    9. w/ Satellite Radio:


      1. Engage the 2 clamps and connect the 2 connectors to the rear pillar RH.

    10. Connect the connector to the air conditioning thermistor assembly.

    11. w/ EC Mirror


      1. Connect the connector to the inner rear view mirror assembly.

  2. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)


    1. A01HVM4E01
      Text in Illustration
      *1 Clip (Black)
      *2 Clip (White)

      Install the 2 clips to the roof headlining assembly.

    2. A01HVF5

      Put the roof headlining assembly into the vehicle through the front door RH.

      Note

      Do not damage the roof headlining assembly or body interior.

    3. Engage the 2 clips and 2 fasteners.

      A01HV4ZE02
      Text in Illustration
      *A w/o Satellite Radio *B w/ Satellite Radio

    4. Install the roof headlining assembly with the 2 clips.

    5. Engage the 4 clamps to the front pillar LH.

    6. Engage the 3 clamps to the front pillar RH.

    7. Connect the bracket with the bolt to the front pillar RH.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    8. w/o Satellite Radio:


      1. Engage the 2 clamps and connect the connector to the rear pillar RH.

    9. w/ Satellite Radio:


      1. Engage the 2 clamps and connect the 2 connectors to the rear pillar RH.

    10. Connect the connector to the sliding roof drive gear assembly.

    11. Connect the connector to the air conditioning thermistor assembly.

    12. w/ EC Mirror


      1. Connect the connector to the inner rear view mirror.

  3. INSTALL VISOR HOLDER


    1. A01HV37

      Engage the 2 claws.

    2. Push in the visor holder as shown in the illustration.

      Tech Tips

      Use the same procedure for the other visor holder.

  4. INSTALL VISOR ASSEMBLY LH


    1. Install the visor assembly LH with the 2 screws.

  5. INSTALL VISOR BRACKET COVER (for LH Side)


    1. A01HSVK

      Engage the 4 claws to install the visor bracket cover.

  6. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  7. INSTALL VISOR BRACKET COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  8. INSTALL SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)


    1. A01HSN6E01
      Text in Illustration
      *1 Notch
      *2 Alignment Mark

      Align the alignment mark on the moulding with the notch of the roof headlining to install the sliding roof opening trim moulding.

      Note

      After installation, check that the corners fit correctly.

  9. INSTALL ASSIST GRIP SUB-ASSEMBLY


    1. A01HW4V

      Put a assist grip sub-assembly together as shown in the illustration.

    2. A01HT67

      Engage the 2 clips to install the assist grip sub-assembly.

    3. A01HTPB

      Engage the 4 claws to install the 2 assist grip covers

      Tech Tips

      Use the same procedure for the RH side.

  10. INSTALL REAR ASSIST GRIP ASSEMBLY LH


    1. A01HVJ3

      Put a rear assist grip assembly LH together as shown in the illustration.

    2. A01HT9Q

      Engage the 2 clips to install the rear assist grip assembly LH.

    3. A01HUMK

      Engage the 4 claws to install the 2 assist grip covers

  11. INSTALL REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  12. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)


    1. A01HTROE01
      Text in Illustration
      *a Switch Part of Room Light Switch Base
      *b Switch Part of No. 1 Room Light Housing

      Align the switch parts shown in the illustration and engage the 4 claws to install the room light switch base to the No. 1 room light housing.

    2. A01HUJTE01
      Text in Illustration
      *a Front

      Engage the 4 claws to install the No. 1 room light housing.

    3. A01HTFHE01
      Text in Illustration
      *a Front

      Engage the 4 claws to install the No. 1 room light lens.

  13. INSTALL SPOT LIGHT ASSEMBLY (w/ Sliding Roof)


    1. A01HUECE01
      Text in Illustration
      *a Front

      Engage the 8 claws to install the 2 map light sub-assemblies to the spot light housing as shown in the illustration.

    2. A01HTGKE01
      Text in Illustration
      *a Front

      Engage the 6 claws to install the spot light housing.

    3. A01HWA2E01
      Text in Illustration
      *a Front

      Engage the 8 claws to install the 2 spot light lenses.

  14. INSTALL ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)


    1. Connect the connector.

    2. A01HVBF

      Engage the 4 clips to install the roof console box assembly.

  15. INSTALL ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)


    1. Connect the connector.

    2. A01HSPK

      Engage the 4 clips to install the roof console box assembly.

  16. INSTALL PROTECTOR


    1. Engage the 2 claws and temporarily install the protector.

  17. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. Engage the 2 claws to temporarily install the inner rear view mirror stay holder cover.

    2. A01HT9U

      Slide the inner rear view mirror stay holder cover as shown in the illustration and engage the 2 guides to install it.

  18. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

    Click here

  19. INSTALL FRONT SEAT ASSEMBLY LH

    for Manual Seat Click here

    for Power Seat Click here

  20. INSTALL FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  21. INSTALL ROOF SIDE INNER GARNISH LH


    1. Engage the guide.

    2. Engage the 5 clips to install the roof side inner garnish LH.

  22. INSTALL CENTER PILLAR UPPER GARNISH LH


    1. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH.

    2. Engage the clip.

    3. Install the center pillar upper garnish LH with the 2 screws.

  23. INSTALL CENTER PILLAR LOWER GARNISH LH


    1. Engage the 2 claws and 3 clips to install the center pillar lower garnish LH.

  24. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. Install the floor anchor of the front seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Check if the ELR locks.

      Note

      The check should be performed with the front seat outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  25. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)


    1. Engage the 3 claws to install the lap belt outer anchor cover.

  26. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01HSLZE01
      Text in Illustration
      *1 Alignment Mark (Pink)

      Align the alignment mark (Pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  27. INSTALL REAR DOOR SCUFF PLATE LH


    1. Engage the 6 claws to install the rear door scuff plate LH.

      Tech Tips

      Engage the claws from the rear side of the scuff plate.

  28. INSTALL ROOF SIDE INNER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  29. INSTALL CENTER PILLAR UPPER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  30. INSTALL CENTER PILLAR LOWER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  31. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  32. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  33. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01HTXUE01
      Text in Illustration
      *1 Alignment Mark (Blue)

      Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  34. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  35. INSTALL REAR SIDE SEATBACK ASSEMBLY RH


    1. Engage the hook to install the rear side seatback assembly RH.

    2. Install the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    3. Connect the connector.

    4. Connect the rear seat outer belt to the rear seat shoulder belt guide RH.

  36. INSTALL REAR SIDE SEATBACK ASSEMBLY LH


    1. Engage the hook to install the rear side seatback assembly LH.

    2. Install the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    3. Connect the connector.

    4. Connect the rear seat outer belt to the rear seat shoulder belt guide LH.

  37. INSTALL REAR SEATBACK ASSEMBLY LH


    1. Place the rear seatback assembly LH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly LH with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    3. Connect the rear seat inner with center belt assembly LH to the rear seat center shoulder belt guide.

  38. INSTALL NO. 2 ROOM PARTITION COVER


    1. A01HW28

      Engage the guide and claw to install the No. 2 room partition cover.

  39. INSTALL REAR SEATBACK ASSEMBLY RH


    1. Place the rear seatback assembly RH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly RH with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  40. INSTALL REAR SEAT CUSHION LOCK HOOK


    1. A01HUP6

      Engage the claw to install a new rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  41. INSTALL REAR SEAT CUSHION ASSEMBLY


    1. Place the rear seat cushion assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. A01HSZN

      Engage the 2 hooks of the seat cushion to the vehicle body as shown in the illustration.

    3. Confirm that the seat cushion is firmly installed.

      Note

      When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.

  42. INSTALL FRONT PILLAR GARNISH LH


    1. Remove the protective cover.

    2. Make sure that the front pillar garnish clip is not damaged.

      Note

      If there is any damage, replace the garnish clip with a new one.

    3. A01HU0V

      Install the front pillar garnish clip to front pillar garnish LH.

      Tech Tips

      Install the front pillar garnish clip so that it faces as shown in the illustration.

    4. Engage the 2 guides as shown in the illustration.

    5. A01HW27

      Engage the 2 clips to install the front pillar garnish LH.

  43. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01HV13E01
      Text in Illustration
      *1 Alignment Mark (Yellow)

      Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  44. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01HSM6

      Insert the 2 clips in the direction indicated by the arrows shown in the illustration to engage them.

    2. Install the cowl side trim sub-assembly LH with the clip.

  45. INSTALL FRONT DOOR SCUFF PLATE LH


    1. Engage the 10 claws to install the front door scuff plate LH.

  46. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  47. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01HV7JE01
      Text in Illustration
      *1 Alignment Mark (White)

      Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  48. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  49. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  50. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  51. INSTALL LUGGAGE TRIM SERVICE HOLE COVER


    1. Engage the claw to connect the luggage trim service hole cover.

  52. INSPECT SRS WARNING LIGHT

    Click here