AIR CONDITIONING AMPLIFIER INSTALLATION


  1. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY


    1. Engage the 2 guides.

    2. Install the air conditioning amplifier assembly with the 2 screws.

    3. Connect each connector.

  2. INSTALL CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/o ECU Integration Box RH)


    1. w/ ECU Integration Box RH:


      1. Engage the 2 claws and install the certification ECU (smart key ECU assembly).

    2. w/o ECU Integration Box RH:


      1. Install the certification ECU (smart key ECU assembly) with the nut and bolt.

      2. Connect each connector.

  3. INSTALL ECU INTEGRATION BOX RH (w/ ECU Integration Box RH)


    1. Install the ECU integration box RH with the 2 nuts and bolt.

      Torque:
      Bolt
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }
      Nut
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    2. Connect each connector.

  4. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Connect each connector.

    2. A01HSAT

      Engage the glove compartment light as shown in the illustration.

    3. A01HTXA

      Engage the 3 guides and 2 clips.

    4. Install the lower instrument panel sub-assembly with the 5 screws <D> or <E>.

  5. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A01HUN4E01
      Text in Illustration
      *1 Airbag Connector
      *2 Airbag Connector Lock

      Connect the airbag connector to the lower No. 2 instrument panel airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. Push in the lock to install the airbag connector.

    5. Temporarily install the lower No. 2 instrument panel airbag assembly with the 3 claws.

    6. Install the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the lower No. 2 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  6. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Connect the connector.

    2. Engage the 2 guides and 4 claws to install the No. 2 instrument panel under cover sub-assembly.

  7. INSTALL INSTRUMENT SIDE PANEL RH


    1. Engage the 3 guides.

    2. A01HVKV

      Engage the 4 claws to install the instrument side panel RH as shown in the illustration.

  8. INSTALL FRONT PANEL GARNISH RH


    1. Engage the 3 claws, 2 clips and 8 guides to install the front panel garnish RH.

  9. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01HV7JE01
      Text in Illustration
      *1 Alignment Mark (White)

      Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  10. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  11. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  12. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  13. INSTALL LUGGAGE TRIM SERVICE HOLE COVER


    1. Engage the claw to connect the luggage trim service hole cover.

  14. INSPECT SRS WARNING LIGHT

    Click here